background image

 

 

Original Instructions 

 

necessary. 

10.  Never operate the machine with damaged guards or without the guarding place   
11.  Keep  hands  and  feet  away  from  the  cutting  means  at  all  times  especially  when  switching  on  the 

motor. 

12.  Take care against injury from any device fitted for trimming the filament line length. 
13.  Never fit metal cutting elements. 
14.  Never use replacement parts or accessories not provided or recommended by the manufacturer. 
15.  Disconnect the machine from the mains before checking, cleaning or working on the machine and 

when it is not in use. 

16.  Inspect  and  maintain  the  trimmer  regularly.  Have  the  trimmer  repaired  only  by  an  authorized 

repairer. 

17.  Take care against injury from the blade fitted for trimming the filament line length. After extending 

the new cutter line, always return the trimmer to its normal operating position before switching on.   

18.  Always ensure that ventilation openings are kept clear of debris. 
19.  When not in use, store the trimmer out of the reach of children. 
20.  For additional protection, it is advised to install a residual current device (RCD) with a rated residual 

operating current not exceeding 30 mAh.   

21.  This appliance is not intended for use by persons (including children) with reduced physical, 

sensory or mental capabilities, or lack of experience and knowledge. Children should be supervised 
to ensure that they do not play with the appliance. 

22.  The nylon line will run on for a few seconds after the tool is switched off! 

  Residual risks 

Even when the tool is used as prescribed it is not possible to eliminate all residual risk factors. 
The following hazards may arise in connection with the tool’s construction and design: 

1.  Damage to lungs if an effective dust mask is not worn. 

2. 

Damage to hearing if effective hearing protection is not worn.

 

3. 

Health defects resulting from vibration emission if the power tool is being used over a longer 
period of time or not adequately managed and properly maintained.

 

WARNING!

  This  machine  produces  an  electromagnetic  field  during  operation.  This  field  may  under 

some circumstances interfere with active or passive medical implants. To reduce the risk of serious or 
fatal  injury,  we  recommend  persons  with  medical  implants  to  consult  their  physician  and  the  medical 
implant manufacturer before operating this machine. 

EXPLANATION OF SAFETY SYMBOLS 

 

- Warning! 

 

- Do not use in rain or wet 

conditions. 

 

Read operator’s manual 

 

- Always wear eye protection. 

 

-Keep bystanders away 

 

Waste electrical products 

should not be disposed of 

with household waste. Please 

recycle where facilities exist. 

Check with your local 

Authority or retailer for 

recycling advice. 

Summary of Contents for H20DC250














Reviews: