background image

8

 

|

 

HENDEN

 INSTALLATION & OWNERS MANUAL

 Henden pH Dosing Pump Owners Manual

OWNERS MANUAL

5. COMMISSIONING AND OPERATION

5.1 Calibration Procedure

This operation is used to set the sensor response reading 
of the pH and peristaltic pump.
Before carrying out the calibration of the probe, remember to:

• 

Stop the filtration pump

• 

Close the isolation valves, if fitted

• 

Remove the probe from the probe holder

• 

Put the shutter washer (fig. 12) in to close off the hole in the 
probe holder

• 

Open the isolation valves, if fitted

• 

Turn on the filtration pump and check that the ON/OFF switch 
(I/O) of the pump is switched to “I”

• 

Carry out the calibration of the probe and repeat the previous 
actions to put the probe back in place. As described in 3.2.3

Nut
Disk brake
Washer seat
Shutter Washer
O-ring

Fig. 11

5.2 Important Points

• 

To ensure the probe signal remains as accurate as possible, 
please follow the procedure as listed below during the 
commissioning of the pool and every 3-4 weeks thereafter, 
or as required.

• 

The procedure is renewed in case of abnormal consumption of 
chemicals.

1.  Remove the protective cap of the probe and keep it for 

reuse at the time of winterising.

Probe

Protective 
Cap

2.  Rinse the probe in tap water for at least 20 minutes.

3.  Next immerse the probe in the pH 7 solution, stir around 

in bottle and leave it in the solution being careful not to 
touch the probe or the cable.

4.  After a period of at least one minute, the stabilised 

value is displayed. Press the CAL button until the display 
shows CAL flashing then release. The quality of the 
probe reading is then briefly displayed.

CAL

SET

pH -

5.  The calibration of the Henden pH Dosing Pump is 

completed: It is now ready to measure the pH of 
your pool.

Summary of Contents for HPHDB













Reviews: