background image

11 

 

If  the  zero  drift  of  the  sensor  is  larger,  ueser  can  do  the  zero 

calibration, this will make the default of target gas concentration as “0”. 

Attention: zero calibration must be in the clean air. 

 
 
6.2.5 Target Calibrate

Only professionl engineer operation allowed

 

OC-1000  multi  gas  and  dust  particle  detector  can  make  the  six  level 

target concentration calibration for the detecting gas, as the picture shows, 
this  must  with  the  standard  concentration  gas, 
pressure relief valve, flowmeter, calibration cap, and 
good connection of gas, or will be prohibited.                                                                                                                 

Operation details: Connecting the device as the 

picture, enter into the target gas calibration interface, 
slowly turn on the calibrate gas and control the flow 
rate  within  500ml/min,  observing  the  detector  gas 
concentration(now should be rising), when the value 
up to the  peak  value  and  keep  stable,  then  choose  a 
non-calibrated  option(“√”  means  been  calibrated, 
“×” means non-calibrated): firstly input the calibrate 
gas  concentration,  then  press  the  “calibrate”.  After  completing  the  target 
point  calibration,  the  target  gas  concentration  of  detector  will  be  the 
calibrate gas concentration. 

 

                                                                                                                                                                                                                                   

                                                                                                                                                                                                                               

6.2.6 Alarming setting 

OC-1000  with  two  adjustable  alarm  threshold  values,  high  alarming 

value  and  low  alarming  value.  When  set  the  low  alarming,  gas 
concentration  lower  than  the  set  value  will  alarm;  when  set  the  high 
alarming , gas concentration higher than the set value will alarm. 

Summary of Contents for OC-1000

















Reviews: