background image

Installation instructions and Instructions for use

Subject to technical modifications 

Date of Issue April/2022

41

Adjusting the awning

Inclination adjustment with tilting arm bearing

Thanks to the tilting arm bearing (1) the 
inclination of the awning and the horizontal 
position of the front rail can be adjusted. 
The inclination angle can be adjusted from 
0° to approx. 40° by means of an adjusting 
spindle (3).
The horizontal position of the front rail is 
adjusted ex works. 
If a modification is required, please proceed 
as described in the following:

Completely extend the awning and take the load off the tilting arm bearing 
(1) during the setting procedure of the adjusting spindle (3) by "slightly" lifting 
the front rail (2). By turning the adjusting spindle by means of an Allen key 6 
mm (4), the awning can be raised or lowered.

Legend

Tilting arm bearing

Adjusting spindle

Front rail

Allen key 6 mm

1

1

3

1

2

0°-40°

1

3

4

Installation instructions and Instructions for use

42

Subject to technical modifications 

Date of Issue April/2022

Adjusting the awning

Arm adjustment

Ex works your awning is optimally adjusted. To ensure a correct closing of the awning, the 
folding arms (1) should be in a parallel position to the front rail (2). The arm bearing bolt is 
mounted in an eccentric bush (6). You can adjust the folding arms at any time as follows:

In order to correct the angle, you must open the fastening screw for the 
eccentric bush (4) by means of an Allen key 2.5 mm (5) first. In order to 
access the threaded pin, you must extend the awning (see illustration on 
the next page).

Then retract the awning to approx. 0.5 m and correct the position of the 
arm by turning the eccentric bush (6) by means of an Allen key 8 mm (7).

Please note:

The position mark (9) of the eccentric bush must be within 

the indicated adjustment range (10). Otherwise the parallelism of the arm 
to the casing can be adjusted, however, the awning will still extend askew.

The arm should be parallel to the casing of the awning! For facilitated 
adjustment, the arm can be supported by hand (8).

Check the adjustment of the inclination and, if necessary, repeat the 
described procedure until the desired result has been reached. 

Now the adjusting procedure of the arm bearing (3) regarding the arms is 
finished. The adjusting procedure on the right side must be performed 
analogously.

Please note:

Finally re-tighten the fastening screws (4)!

Installation instructions and Instructions for use

Subject to technical modifications 

Date of Issue April/2022

43

Adjusting the awning

Arm adjustment

Legend

Folding arm

Lifting the folding arm

Front rail

Position mark of the eccentric bush

Arm bearing

Adjustment range (opposite side in 
mirror image)

Clamping screw for eccentric bush

Rear stay pipe

Allen key AF2.5

Bottom stay pipe

Eccentric bush for arm adjustment

Wall / rear side

Allen key A/F 8

10

min.

max.

2

8

1

13

3

11

5

4

6

7

12

4

6

9

3

Installation instructions and Instructions for use

44

Subject to technical modifications 

Date of Issue April/2022

Adjusting the awning

Adjusting the cover support

From a width of 4501 mm, the foldig arm awning AREIA is provided with a cover support 
(3).

If you want to change the inclination of the awning, you should adjust the cover support in 
such a way, that the awning cover does not touch on the cover support when it is 
tensioned. Loosen the fixing screws (5) slightly. Now you can turn the plastic tray of the 
cover support (3). Afterwards, tighten the fixing screws (5) again.

Legend

Stay pipe
Roller tube
Fabric support
Allen key
Fixing screw

1

2

3

4

5

Summary of Contents for AREIA 7040






















Reviews: