background image

Hella marine LED Navigation Lamps offer many advantages over conventional bulb lamps.  

Significantly reduced power consumption, ultra long life and high tolerance to shock and 

vibration make the LED lamps the ideal choice for the harsh marine environment.

The Hella marine NaviLED

®

360 series are Precision Optical Instruments, tested and type 

approved to comply with international maritime regulations. They are covered by a 5 year 

warranty.

Wiring and Electrical Protection

LED modules are polarity conscious. 

This lamp is protected against reverse polarity connection, 

reverse polarity will not damage this product but will inhibit its function. 

HELLA marine recommends wire connections be soldered, and heat shrink tubing applied to seal 

the joint. 

Each lamp must be protected against short circuit by a fuse rated at 5 amperes maximum. 

Note:

 Do not attempt to open, no serviceable part inside.

Electromagnetic Compatibility (EMC)

This LED lamp is an electronic device. The electrical circuits contain components that suppress 

possible interference, both emission as well as susceptibility, to the limits prescribed in 

international regulations.

Colour 

Connect to

Black 

Negative (-ve)

Red 

Signal (+ve)

Wiring Colour Coding

Designed and Manufactured in New Zealand

958 315-60 V01 (ENG-GER-FR)

INSTRUCTION SHEET: NaviLED

®

360 Compact Pole Mount

2 Nautical Mile All Round White / Anchor Lamp

Product Specifications
Housing Material  

UV resistant high impact plastic

Lens Material 

Heavy duty Grilamid

®

Minimum Visible Distance

 

2 Nautical Miles

Cable 

Pre-wired with twin core marine cable

Operating Voltage 

Multivolt

TM

 9-33V DC

Power Consumption

 

Less than 1W  (0.08A @ 12V / 0.04A @ 24V)

Degree of Protection 

IP 67 - Completely Sealed

Approvals

 

USCG, IMO COL REG 72, Wheelmark

Correct Positioning

 

NaviLED

®

360 Compact All Round / Anchor 

Lamps must be installed as follows:

When the lamp operates, the light should not

 

be obstructed or concealed by masts, 

topmasts or structures, i.e. Installed on the 

highest point of a vessel so the light arc is 

unbroken.

 

All Round lamps must be positioned as close 

as practicable to the fore and aft centre line 

of a vessel. (see Fig.1)

 

The All Round white lamp on a power driven 

Vessel less than 12m in length shall be 

installed at least one meter higher than the 

sidelights. 

The lamp must be installed so that the 

horizontal surface of the base is parallel to 

the vessel's water line. (See Fig.2)

Fig. 1   

On the fore and aft centre line.

Fore

Centre Line

Aft

Fig. 2  

Installed with base parallel to vessel's  

 

water line.

Vessel's water Line

Installation Instructions

1.   Fixed Pole mount:

  Ensure mounting surface is flat and on the vessels centre line (see above).  

 

Use the provided screws to secure taking care not to over tighten.

 

2.   Fold-down Pole mount:

 A removable wedge is supplied for installations onto different surface  

 

cambers. Use the provided screws to secure taking care not to over tighten. Once mounted the  

 

base can be adjusted through 180 degrees, when the desired angled is reached secure by 

 

tightening the locking collar.

 

3.   Plug-in Pole mount:

 Mount base separately and connect wiring. Use the provided screws to  

 

secure taking care not to over tighten. Insert lamp into base and fix with locking collar. 

 

Ensure rubber cap, as provided, is used to cover socket when pole is removed.

   1. Fixed pole 

                         2. Fold-down pole                  3. Plug-in pole

MAX 3 Nm

MAX 3 Nm

MAX 3 Nm

The Hella marine Series 2010 navigation and signal lamps comply with USCG A-16 requirements for 
powerboats and/or sailing vessels up to 12 m (39’) in length.

Mounting position of the lamps:

- Port and starboard navigation lamps (3) must be mounted with their back plate parallel to the vessel 
centre line (6), in the same thwartships position (5) and at the same height above the waterline (4). 
- Masthead (1) and stern lamps (2) as well as anchor lights must be mounted above the vessel centre 
line (6).
- All lamps must be mounted in a vertical position with their back plate perpendicular to the waterline.
- When operating, the light should not be obstructed or concealed by superstructures, other objects or 
persons. The lamps should also be tightly secured in position

2010 series lamps Mounting Instructions

*

) Angle of 7.5 ° 

(25° for sailing vessels).

Maintenance

-  The lens may be cleaned with a soft brush.
-  Only cleansers suitable for polycarbonate plastic may be used.
-  Do not wash with harsh or abrasive cleaners.

(1)  Masthead lamp (white)

(2)  Stern lamp (white)

(3)  Starboard / port lamp

(4)  Waterline (CWL)

(5)  Thwartships plane

(6)  Vessel centre line

(7)  green

(8)  red

(9)  white

Mounted with 

swivel bracket

Mounted with 

plug-in bracket

Ø 3mm

Ø 3mm

Ø 3mm

Ø 3mm

Mounted with tel-

escope bracket 

Mounted with 

standard bracket

993 609-00

The Hella marine Series 2010 navigation and signal lamps comply with USCG A-16 requirements for 
powerboats and/or sailing vessels up to 12 m (39’) in length.

Mounting position of the lamps:

- Port and starboard navigation lamps (3) must be mounted with their back plate parallel to the vessel 
centre line (6), in the same thwartships position (5) and at the same height above the waterline (4). 
- Masthead (1) and stern lamps (2) as well as anchor lights must be mounted above the vessel centre 
line (6).
- All lamps must be mounted in a vertical position with their back plate perpendicular to the waterline.
- When operating, the light should not be obstructed or concealed by superstructures, other objects or 
persons. The lamps should also be tightly secured in position

2010 series lamps Mounting Instructions

*

) Angle of 7.5 ° 

(25° for sailing vessels).

Maintenance

-  The lens may be cleaned with a soft brush.
-  Only cleansers suitable for polycarbonate plastic may be used.
-  Do not wash with harsh or abrasive cleaners.

(1)  Masthead lamp (white)

(2)  Stern lamp (white)

(3)  Starboard / port lamp

(4)  Waterline (CWL)

(5)  Thwartships plane

(6)  Vessel centre line

(7)  green

(8)  red

(9)  white

Mounted with 

swivel bracket

Mounted with 

plug-in bracket

Ø 3mm

Ø 3mm

Ø 3mm

Ø 3mm

Mounted with tel-

escope bracket 

Mounted with 

standard bracket

993 609-00

The Hella marine Series 2010 navigation and signal lamps comply with USCG A-16 requirements for 
powerboats and/or sailing vessels up to 12 m (39’) in length.

Mounting position of the lamps:

- Port and starboard navigation lamps (3) must be mounted with their back plate parallel to the vessel 
centre line (6), in the same thwartships position (5) and at the same height above the waterline (4). 
- Masthead (1) and stern lamps (2) as well as anchor lights must be mounted above the vessel centre 
line (6).
- All lamps must be mounted in a vertical position with their back plate perpendicular to the waterline.
- When operating, the light should not be obstructed or concealed by superstructures, other objects or 
persons. The lamps should also be tightly secured in position

2010 series lamps Mounting Instructions

*

) Angle of 7.5 ° 

(25° for sailing vessels).

Maintenance

-  The lens may be cleaned with a soft brush.
-  Only cleansers suitable for polycarbonate plastic may be used.
-  Do not wash with harsh or abrasive cleaners.

(1)  Masthead lamp (white)

(2)  Stern lamp (white)

(3)  Starboard / port lamp

(4)  Waterline (CWL)

(5)  Thwartships plane

(6)  Vessel centre line

(7)  green

(8)  red

(9)  white

Mounted with 

swivel bracket

Mounted with 

plug-in bracket

Ø 3mm

Ø 3mm

Ø 3mm

Ø 3mm

Mounted with tel-

escope bracket 

Mounted with 

standard bracket

993 609-00

Reviews: