CONGRATULATIONS! You’ve
purchased the finest in natural lighting
technology with your new OttLite
product.
PRODUCT REGISTRATION FORM
Please complete the enclosed Product
Registration Form and return it today
by mail, or register online by going to:
http://warranty.OttLite.com.
WARNING: To prevent electric shock,
make sure the lamp is not plugged in
until all assembly steps are complete.
To avoid lamp tip over, position lamp
shade as shown in diagram.
LAMP ASSEMBLY
1.
Remove lamp from packing placing
the base
(A) flat on a steady surface.
2. Thread pole (B) to base (A) by hand,
turning clockwise until snug. Excess
cord may be pulled through the base.
3. Attach counterbalance (C) to arm (E)
by turning clockwise until snug, then
finish threading arm
(E) into pole (B).
4. Fit shade (H) over socket (G) then
thread socket ring
(J) onto socket.
Turn socket ring
(J) clockwise to tight-
en until finger tight and the shade
(H)
is held securely.
5. Refer to BULB INSERTION/
REMOVAL to install bulb (K) in lamp.
6. Plug the cord into a standard 120Vac
outlet.
7. To turn the lamp ON or OFF rotate the
switch
(M) clockwise.
8. To position the upper arm (E), turn
thumbscrew
(D) counterclockwise to
loosen, reposition arm
(E) then turn
thumbscrew
(D) clockwise to tighten.
To avoid damage to the lamp,
DO
NOT ATTTEMPT to move arm (E)
without loosening thumbscrew
(D).
9. DO NOT try to rotate the shade side-
ways as the lamp maybe damaged.
DO NOT force thumbscrew as damage
to the lamp may occur.
BULB INSERTION/REMOVAL
1. Make sure the lamp is not plugged into
an electrical socket.
2. If the lamp has been in use, allow it to
cool approximately 5 minutes before
proceeding.
3. To install the bulb (K) in the socket (G),
thread the base of the bulb into the
socket turning clockwise until snug.
CAUTION: DO NOT overtighten the
bulb. Overtightening the bulb may
make removal difficult or damage
the lamp or bulb.
4. To remove a bulb (K) already installed
in the lamp, unthread the bulb from the
socket
(G) turning counterclockwise to
loosen.
DO NOT allow glass part of the bulb to
strike the shade or any hard surface.
Please note that in operation, OttLite
bulbs are not dimmable.
Enjoy your OttLite Cambridge
Table Lamp!
This lighting system is designed
for use with OttLite type
(style number ED15-S). Use of other
products voids the warranty and
may result in damage to the lighting
system.
15w Cambridge Table Lamp
CAUTION!
If the external flexible cable or cord of this luminaire is damaged, it shall be exclusively replaced by the manufac-
turer or its service agent or a similar qualified person in order to avoid a hazard. Indoor use only.
15w Cambridge Table Lamp
15548BB8
15548BZH
15548BZP
S2471
CAUTION! IMPORTANT SAFETY INSTRUCTIONS:
THIS PORTABLE LAMP HAS A POLARIZED PLUG (ONE BLADE IS WIDER THAN THE OTHER) AS A FEATURE TO
REDUCE THE RISK OF ELECTRIC SHOCK. THIS PLUG WILL FIT IN A POLARIZED OUTLET ONLY ONE WAY. IF
THE PLUG DOES NOT FIT FULLY IN THE OUTLET, REVERSE THE PLUG. IF IT STILL DOES NOT FIT, CONTACT A
QUALIFIED ELECTRICIAN. NEVER USE WITH AN EXTENSION CORD UNLESS PLUG CAN BE FULLY INSERTED.
DO NOT ALTER THE PLUG.
CAUTION:
TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT,
FULLY INSERT.
AVERTISSEMENT! IMPORTANTES DIRECTIVES
DE SÉCURITÉ:
CETTE LAMPE PORTATIVE EST MUNIE D’UNE FICHE POLARISÉE (UNE LAME PLUS LARGE QUE L’AUTRE). CE
DISPOSITIF DE SÉCURITÉ DIMINUE LE RISQUE DE CHOCS ÉLECTRIQUES PUISQUE LA FICHE NE S’INSÈRE
DANS LA PRISE QUE D’UN SEUL CÔTÉ. SI ELLE N’ENTRE PAS DANS LA PRISE, INVERSEZ-LA. SI ELLE
N’ENTRE TOUJOURS PAS, CONTACTEZ UN ÉLECTRICIEN QUALIFIÉ. N’UTILISEZ JAMAIS AVEC UNE RALLONGE
SAUF SI LA FICHE S’INSÈRE ENTIÈREMENT. NE MODIFIEZ PAS CE DISPOSITIF DE SÉCURITÉ.
AVERTISSEMENT:
POUR ÉVITER LES CHOCS ÉLECTRIQUE, INSÉREZ LE BOUT LARGE
DE LA FICHE DANS LA GRANDE FENTE ET POUSSEZ JUSQU’AU BOUT.
¡PRECAUCIÓN! INSTRUCCIONES DE
SEGURIDAD IMPORTANTES:
ESTA LÁMPARA PORTÁTIL TIENE UN ENCHUFE POLARIZADO (UNA DE SUS PATAS ES MÁS ANCHA QUE LA
OTRA) COMO CARACTERISTICA PARA REDUCIR EL RIESGO DE UNA DESCARGA ELÉCTRICA. ESTE ENCHUFE
ENCAJARÁ EN CUALQUIER TOMACORRIENTE POLARIZADO SOLO DE UNA MANERA. SI EL ENCHUFE NO CALZA
COMPLETAMENTE EN EL TOMACORRIENTE DÉLE LA VUELTA. SI AÚN NO ENCAJA, PÓNGASE EN CONTACTO
CON UN ELECTRICISTA CALIFICADO. NUNCA UTILICE UNA EXTENSIÓN A NO SER QUE EL ENCHUFE PUEDA
SER TOTALMENTE INSERTADO. NO ALTERE EL ENCHUFE.
PRECAUCIÓN:
PARA PREVENIR UNA DESCARGA ELÉCTRICA, HAGA COINCIDIR LA PATA
ANCHA DEL ENCHUFE CON LA RANURA ANCHA, INSERTE TOTALMENTE.
ENGLISH
INS-14-0150 REV101314
CONGRATULATIONS! You’ve
purchased the finest in natural lighting
technology with your new OttLite
®
product.
PRODUCT REGISTRATION FORM
Please complete the enclosed Product
Registration Form and return it today
by mail, or register online by going to:
http://warranty.OttLite.com.
WARNING: To prevent electric shock,
make sure the lamp is not plugged in
until all assembly steps are complete.
To avoid lamp tip over, position lamp
shade as shown in diagram.
LAMP ASSEMBLY
1.
Remove lamp from packing placing
the base (A) flat on a steady surface.
2. Loosen, but do not remove, thumb-
screw (D) at the joint on arm (E).
3.
To aid in assembly of step 6, rotate
the joint so that it points opposite to the
arm (E). Tighten thumbscrew (D) by hand
until snug.
4. Thread pole (B) to the joint of arm (E)
by hand carefully turning clockwise. DO
NOT tighten completely.
5. Hold arm (E) to steady pole (B) then
thread pole (B) to base (A) by hand care-
fully turning clockwise until snug. Arm (E)
will still be loose. Excess cord may be
pulled through the base (A).
6. Finish threading arm (E) to pole (B) by
hand turning clockwise until snug.
7. Attach shade (H) to socket housing (G)
using socket ring (J) to hold the shade in
place.
8. Thread socket ring (J) onto socket by
hand turning clockwise until tight enough
to hold the shade steady.
9. Thread arm (C) into joint of pole (E) by
hand turning clockwise until tight.
10. Refer to BULB INSTALLATION AND
REMOVAL to install bulb (K) in lamp.
11. Plug the cord into a standard 120Vac
outlet.
12.
To turn the lamp on or off rotate the
power cord mounted switch (M)
clockwise.
13. To position arm (E) turn thumbnut (D)
counterclockwise to loosen, reposition
arm (E) then turn thumbnut (D) clockwise
to tighten. To avoid damage to the lamp
DO NOT ATTEMPT to move arm (E)
without loosening thumbnut (D).
14. DO NOT try to rotate the shade side-
ways as the lamp maybe damaged.
DO NOT force thumbscrew as damage
to the lamp may occur.
BULB INSERTION/REMOVAL
1. Make sure the lamp is not plugged into
an electrical socket.
2. If the lamp has been in use, allow it to
cool approximately 5 minutes before
proceeding.
3. To install the bulb (K) in the socket
(G), thread the base of the bulb into the
socket turning clockwise until snug.
CAUTION: DO NOT overtighten the
bulb. Overtightening the bulb may
make removal difficult or damage the
lamp or bulb.
4. To remove a bulb (K) already installed
in the lamp, unthread the bulb from the
socket (G) turning counterclockwise to
loosen.
Please note that in operation, OttLite
®
bulbs are not dimmable.
Enjoy your OttLite
®
Cambridge Table
Lamp!
This lighting system is designed
for use with OttLite
®
type
(style number ED15-S). Use of other
products voids the warranty and
may result in damage to the lighting
system.
Cambridge Table Lamp
CAUTION!
If the external flexible cable or cord of this luminaire is damaged, it shall be exclusively replaced by the manufac-
turer or its service agent or a similar qualified person in order to avoid a hazard. Indoor use only.
REV022111
15w Cambridge Table Lamp
15548BB8
ST10086
CAUTION! IMPORTANT SAFETY INSTRUCTIONS:
THIS PORTABLE LAMP HAS A POLARIZED PLUG (ONE BLADE IS WIDER THAN THE OTHER) AS A FEATURE TO
REDUCE THE RISK OF ELECTRIC SHOCK. THIS PLUG WILL FIT IN A POLARIZED OUTLET ONLY ONE WAY. IF
THE PLUG DOES NOT FIT FULLY IN THE OUTLET, REVERSE THE PLUG. IF IT STILL DOES NOT FIT, CONTACT A
QUALIFIED ELECTRICIAN. NEVER USE WITH AN EXTENSION CORD UNLESS PLUG CAN BE FULLY INSERTED.
DO NOT ALTER THE PLUG.
CAUTION:
TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT,
FULLY INSERT.
AVERTISSEMENT! IMPORTANTES DIRECTIVES
DE SÉCURITÉ:
CETTE LAMPE PORTATIVE EST MUNIE D’UNE FICHE POLARISÉE (UNE LAME PLUS LARGE QUE L’AUTRE). CE
DISPOSITIF DE SÉCURITÉ DIMINUE LE RISQUE DE CHOCS ÉLECTRIQUES PUISQUE LA FICHE NE S’INSÈRE
DANS LA PRISE QUE D’UN SEUL CÔTÉ. SI ELLE N’ENTRE PAS DANS LA PRISE, INVERSEZ-LA. SI ELLE
N’ENTRE TOUJOURS PAS, CONTACTEZ UN ÉLECTRICIEN QUALIFIÉ. N’UTILISEZ JAMAIS AVEC UNE RALLONGE
SAUF SI LA FICHE S’INSÈRE ENTIÈREMENT. NE MODIFIEZ PAS CE DISPOSITIF DE SÉCURITÉ.
AVERTISSEMENT:
POUR ÉVITER LES CHOCS ÉLECTRIQUE, INSÉREZ LE BOUT LARGE DE LA
FICHE DANS LA GRANDE FENTE ET POUSSEZ JUSQU’AU BOUT.
¡PRECAUCIÓN! INSTRUCCIONES DE SEGURIDAD
IMPORTANTES:
ESTA LÁMPARA PORTÁTIL TIENE UN ENCHUFE POLARIZADO (UNA DE SUS PATAS ES MÁS ANCHA QUE LA
OTRA) COMO CARACTERISTICA PARA REDUCIR EL RIESGO DE UNA DESCARGA ELÉCTRICA. ESTE ENCHUFE
ENCAJARÁ EN CUALQUIER TOMACORRIENTE POLARIZADO SOLO DE UNA MANERA. SI EL ENCHUFE NO CALZA
COMPLETAMENTE EN EL TOMACORRIENTE DÉLE LA VUELTA. SI AÚN NO ENCAJA, PÓNGASE EN CONTACTO
CON UN ELECTRICISTA CALIFICADO. NUNCA UTILICE UNA EXTENSIÓN A NO SER QUE EL ENCHUFE PUEDA
SER TOTALMENTE INSERTADO. NO ALTERE EL ENCHUFE.
PRECAUCIÓN:
PARA PREVENIR UNA DESCARGA ELÉCTRICA, HAGA COINCIDIR LA PATA
ANCHA DEL ENCHUFE CON LA RANURA ANCHA, INSERTE TOTALMENTE.
ENGLISH
A
C
L
M
B
K
J
G
H
E
D