19
Initial start-up and functions
1
Optical Input (optional)
Optical input in SPDIF format for connecting signal
sources with a digital audio output. The sampling
rate of this input must be between 28 and 96 kHz.
Please note:
The digital input is not part of the
C ONEs standard equipment. This can only be ret-
UR¿WWHG ZLWK WKH RSWLRQDOO\ DYD(/,; 'LJLWDO
Input Module HDM 1.
Important:
The signal of a digital audio source nor-
mally does not contain any information about the
YROXPHOHYHO.HHSLQPLQGWKDWWKLVZLOOOHDGWRIXOO
OHYHORQWKHRXWSX(/,;&21(7KLVPD\
FDXVHVHYHUHGDPDJHWR\RXUVSHDNHUV:HVWURQJ
-
O\UHFRPPHQGWRRQO\XVHYROXPHFRQWUROOHGDXGLR
sources!
Note:
7KLV DPSOL¿HU FDQ RQO\ KDQGOH VWHUHR LQSXW
signals and no MP3- or Dolby-coded digital audio
stream!
Note:
It is possible to use the
Optical Input
and the
ORZOHYHO
Line Input
at the same time.
2
SPDIF Direct In switch (optional)
Due to the
SPDIF Direct In switch
, the input stages
of the C ONE can be bypassed and the input sig-
nal of the
Optical Input
directly and losslessly rout-
HGIURPWKHLQWHJUDWHG'$FRQYHUWHUWRWKHLQWHUQDO
SRZHU VWDJH 7R DFWLYDWH WKH GLUHFW VLJQDO URXWLQJ
\RXKDYHWRVHWWKH
SPDIF Direct In switch
to “On”.
Please note:
The
SPDIF Direct In
function is not
part of the C ONEs standard equipment. It is solely
LQFOXGHGLQWKHRSWLRQDOO\DY(/,;'LJLWDO,Q
-
put Module HDM 1.
Note:
7KLVVZLWFKRQO\DႇHFWVWKHVLJQDOURXWLQJRI
the
Optical Input
.
Note:
7KH DPSOL¿HU PXVW EH RSHUDWHG LQ IXOOUDQJH
mode for routing the digital input signal directly to
the power stage. Therefore change the position of
the
X-Over switch
to “FULL“ (see page 21, item 23).
Note:
,IWKHVZLWFKLVVHWWR³2Q´SRVLWLRQWKHORZOHY
-
el
Line Input
(3) as well as the
Level control
(16) are
without function!
3
Line Input
FKDQQHO ORZOHYHO OLQH LQSXW WR FRQQHFW VLJQDO
sourc es such as head units / radios / DSPs.
4
GND
The ground cable should be connected to a common
ground reference point (this is located where the
QHJDWLYHWHUPLQDORIWKHEDWWHU\LVJURXQGHGWRWKH
PHWDOERG\RIWKHYHKLFOHRUWRDSUHSDUHGPHWDOOR
-
FDWLRQRQWKHYHKLFOHFKDVVLVLHDQDUHDZKLFKKDV
been cleaned of all paint residues. Recommended
cross section: min. 16 mm² / AWG 6.
5
+12 V
&RQQHFWWKH9SRZHUFDEOHWRWKHSRVLWLYHWHU
-
minal of the battery. Recommended cross section:
min. 16 mm² / AWG 6.
6
REM
The remote lead should be connected to the remote
RXWSXW DXWRPDWLF DQWHQQD DHULDO SRVLWLYH RXWSXW
RI WKH KHDG XQLW FDU UDGLR7KLV LV RQO\ DFWLYDWHG
if the head unit / car radio is switched on. Thus the
DPSOL¿HU LV VZLWFKHG RQ DQG Rႇ WRJHWKHU ZLWK WKH
head unit / car radio. As soon as there is an addi-
tional digital signal processor (DSP) implemented in
the signal path, the remote output of the DSP has to
be used to turn on the C ONE.
7
TwinPower Link switch
7KH +(/,; & 21( DPSOL¿HU FDQ EH FRQQHFWHG WR
D VHFRQG & 1( YLD WKH
TwinPower Link
by which
the output power is more than doubled, depending
RQ WKH VSHDNHU FRQ¿JXUDWLRQ ,Q RUGHU WR RSHUDWH
WZRDPSOL¿HUVLQWKLVPRGHWKH\PXVWEHFRQQHFW
-
ed with a RCA / Cinch cable (see page 19, item 8;
Mono RCA/Cinch In- / Output
7KHDPSOL¿HUZKLFK
is set as “Master” assumes the complete control
DFWLYH FURVVRYHU EDVV ERRVW HWF IRU ERWK DPSV
$OO¿OWHUDGMXVWPHQWVRIWKHDPSOL¿HUZKLFKRSHUDWHV
LQ³6ODYH´PRGHZLOOEHGHDFWLYDWHG
Attention:
0DNHVXUHWKDWRQHDPSOL¿HULVDGMXVWHG
DV ³0DVWHU´ DQG WKH RWKHU RQH DV ³6ODYH´ ,Q WKLV
mode the minimum speaker impedance is 2 Ohms.
Note:
,IWKHDPSOL¿HURSHUDWHVLQGLYLGXDOO\WKH
Twin-
Power Link
switch must be set to “Master”.
([DPSOHVIRUVSHDNHUFRQ¿JXUDWLRQVLQ7ZLQ3RZHU
Link mode can be found on page 26.
8
Mono RCA/Cinch In- / Output
7KLV FRQQHFWRU VHUYHV DV VLJQDO LQ RU RXWSXW IRU
FRQQHFWLQJ D IXUWKHU & 21( DPSOL¿HU LQ EULGJH
mode (see page 19, item 7;
TwinPower Link switch
).
