background image

 

 

 
 

Helgi Europe 

Via Artigiani 29/31 29020 Vigolzone (PC) Italy 

[email protected] | [email protected] 

www.helgi-solutions.com 

 

 

4.0 OPERATION 

 

4.1 GENERAL DESCRIPTION 

After the electrical connections, make sure of the exact voltage of the power supply, close the circuit and 

giving power and operate with short pulses on the inverter "Lowering." Make sure everything runs properly 

and then operate few times the up/down mechanism. At this point the operation was well performed. 

 

5.0 USE 

 

5.1 SETTING THE LIMIT SWITCHES 

The only adjustment to be made is that of the two up and down switches up of the projection screen. These 

two elements are already set during production, by the manufacturer. 

However, you can make some adjustments by turning the two limit switches screws, which can be reached 

by introducing a 4 mm hexagonal key – standard supplied - in the two holes on the bottom of the screen 

case. 

IMPORTANT!

 Do not unroll the canvas over the measurement specified for each type of screen: increasing 

the descent above this size could damage the screen or cause its fall off, such damages are not covered by 

warranty and are not under the responsibility of the manufacturer. 

Likewise, do not force the rewinding of the canvas after it has been completely rolled up as this would force 

the electric motor and the counter weight tube could get stacked into the box and consequently get 

damaged. 

 

Summary of Contents for VIDEO MOTORE PROJECTION SCREEN











Reviews: