Hefter TF MEGA-A Instruction Manual Download

Page: 33 / 71

3-3

Chapter3 Advanced Operation

Paper set lever

Lower the paper set lever.

The paper feed tray will be raised.

Make sure that you lower the paper set

lever. If you start operations without the

paper set lever lowered, the paper feed

rings will run idle, causing the machine

to stop.

Single fold

Count:0

Press the

key to select a paper

size.

Double fold

Count:0

Press the key to select [Double fold].

Stacker roller

Lever

Belt

Stacker lever

While lifting up the stacker rollers with

your hand, pull the levers (left and

right) attached to the stacker lever

in the direction of the arrow so that

contact pressure on the belts by the

stacker rollers is relieved.

Press the key for test folding.

The stacker rollers will move to the position of

"5."
For double letter size, the stacker rollers will

move to the position of "4." (North America)
Check if the paper is ejected smoothly.
If mis-feed or double-feed occurs, refer to

Chapter2 "Basic Operation" “1.Standard

Folding of Standard Paper” "1-3. Operation

Procedures ( p.2-2).

SR set

If the paper is not ejected smoothly,

change the position of the stacker

rollers to "4" or "3."

While pressing the key, press the key to

change [SR set] from [5] to [4] or [3].

Summary of Contents for TF MEGA-A








































































Search results

Summary of Contents for TF MEGA-A

Reviews:

Related manuals for TF MEGA-A

Brands by name

Popular brands

Hefter TF MEGA-A, Instruction Manual

Search results

Summary of Contents for TF MEGA-A

Reviews:

Related manuals for TF MEGA-A

Brands by name

Popular brands