manualshive.com logo in svg

HEAVTH HF100, Technical Manual, Page: 12 / 14

Share
Download
HEAVTH HF100 Technical Manual Download Page 12

HF100 

CapecitanceHeightControler                                                                                         

http://www.heavth.com 

第

  - 12 - 

页

 

共

  14 

页

 

cable. 
 

The sensor is mounted on the torch and that the torch nozzle is positioned in the 

middle of the ring. 
 

The following parts are connected to the protective conductor bus: machine earth 

ground (GND).torch table and ground screw on HF100 using a cable with a 
cross-section of 14 AWG (2.5 mm2). 
 

2. 

First, set on Manual mode, lift torch up over 20mm against steel plate. 

 

3. 

Turn the SENSITIVITY and DISTANCE in the middle position. 

 

4. 

Press Auto Test button to turn Auto on, if torch lift down, means Auto Height 

is too low, then adjust RP4 clockwise to raise the auto height. If torch lift up, means 
Auto height is too high, turn anti-clockwise. 
 

Please protect the adjust Resistor to avoid damage, Do Not exceed 1/4 round on 

every turn, and make record of turn direction.   
 

5. 

Attach the control box to the back panel and secure with four (4) screws. 

 

6. 

Configure the clearance distance and sensitivity. 

 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Summary of Contents for HF100















Reviews:

No comments