manualshive.com logo in svg

HeatStar HSVFBF10LPTS, Operating Instructions And Owner'S Manual, Page: 15 / 16

Share
Download
HeatStar HSVFBF10LPTS Operating Instructions And Owner'S Manual Download Page 15

15

Installation Instructions and Owner’s Manual

Unvented Liquid Propane Fired Room Heater

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

17

18

19

WARNING:

 Failure to position the parts in accordance with these diagrams or failure to use only parts specifi cally approved with this 

heater may result in property damage or personal injury.

MODEL: HSVFRD10LPTS

ITEM

P/N

PART DESCRIPTION

QTY

ITEM

P/N

PART DESCRIPTION

QTY

1

80040

Wire Guard

1

11

80020

Regulator Connection

1

2

80051

Front Panel

1

12

80058

Floor Mounting Feet

1

3

80024

Reflector

1

13

80052

Back Panel

1

4

80030

Burner Assembly

1

14

80036

Wall Mounting Bracket

1

5

80056

ODS Pilot Assembly w/ Thermocouple (LP)

1

15

80028

Heat Shield

1

6

80032

ODS Bottom Bracket

1

16

80053

Back Heat Shield

1

7

80050

Fireproof Plate

1

17

70640

Thermostat Valve

1

8

80016

Elbow Adapter(90

°

 Regulator Connection)

1

18

80019

Ignitor Pulse

1

9

80078

Regulator

1

19

80014

Ignitor Wire

1

10

80055

Regulator Mounting Bracket

1

PARTS LIST AND DIAGRAM 

Summary of Contents for HSVFBF10LPTS

















Reviews:

No comments