manualshive.com logo in svg

HeatStar HSVFBF10LPTS, Operating Instructions And Owner'S Manual, Page: 1 / 16

Share
Download
HeatStar HSVFBF10LPTS Operating Instructions And Owner'S Manual Download Page 1

1

Installation Instructions and Owner’s Manual

Unvented Liquid Propane Fired Room Heater

HEATSTAR, 4560 W. 160

TH

 ST., CLEVELAND, OHIO 44135 · 800-251-0001

2016 - CB

Installer: Leave this manual with the appliance. Consumer: Retain this manual for future reference. 

UNVENTED LP-GAS FIRED ROOM HEATER

HSVFBF10LPTS

HSVFRD10LPTS

OPERATING INSTRUCTIONS 

AND OWNER’S MANUAL

READ INSTRUCTIONS CAREFULLY:

 Read and follow all instructions. Place instructions in a safe 

place for future reference. Do not allow anyone who has not read these instructions to assemble, 
light, adjust or operate the heater.

Model #

 

WARNING:

 If the information in this manual is not followed exactly, a fi re or explosion may result causing 

 

property damage, personal injury, or loss of life. 

- Do not store or use gasoline or other fl ammable vapors and liquids in the vicinity of this or any other appliance.

- WHAT TO DO IF YOU SMELL GAS

 

• Shut off gas supply

 

• Do not try to light any appliance

 

• Do not touch an electrical switch; do not use any phone in your building.

 

• Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions.

 

• If you cannot reach your gas supplier, call the fi re department.

- Installation and service must be performed by a qualifi ed installer, service agency, or the gas supplier.

WARNING

: This is an unvented gas-fi red heater. It uses air (oxygen) from the room in which it is installed. 

Provisions for adequate combustion and ventilation air must be provided. Refer to Fresh Air for Combustion and 
Ventilation section on page 4 of this manual. 

WARNING

: Improper installation, adjustment, alteration, service or maintenance can cause injury or property 

damage. Refer to this manual for correct installation and operational procedures. For assistance or additional 
information consult a qualifi ed installer, service agency, or gas supplier. 

This appliance may be installed in an aftermarket permanently manufactured (mobile) home, where not prohibited 
by local codes. This appliance is only for use with the type of gas indicated on the rating plate. This appliance is not 
convertible for use with any other gas. 

Blue Flame Heaters

HSVFBF10LPTS

Plaque Heaters 

HSVFRD10LPTS

Summary of Contents for HSVFBF10LPTS

















Reviews:

No comments