Heatrae Sadia Express 50 Litres Installation, Operation And Maintenance Manual Download Page 4

4

2. Safety

Do not connect any pressure-relief device 

to the vent pipe of this water heater.

How hot water can be drained. (see page 11  

for more details).

If the supply cord is damaged, it must 

be replaced by the manufacturer, its service 

agent or simularly qualified persons in order 

to avoid a hazard.

2.1 General safety warnings

2.2 Recommendations

2.3 Specific safety instructions

WARNING

  Install only as a CISTERN FED 

appliance, failure to do so will invalidate 

any guarantee and may lead to a 

dangerous installation.

CISTERN FED INSTALLATION

  When installed as a Cistern Fed water 

heater the cold water supply must be 

from a feed cistern complying with 

Water Regulations Schedule 2, section 

7, paragraph 16.

  A vent pipe must be connected to the 

vented top of the heater. The vent pipe 

must rise continuously and be arranged 

to discharge into the cold water feed 

cistern.

  The vent pipe must have a minimum 

bore of 19mm.

  More than one conventional tap can be 

supplied.

WARNING

  Only competent persons  having 

received adequate training are 

permitted to work on the appliance and 

the installation.

  Do not tamper with any of the safety 

valves or controls supplied with the 

appliance.

  Before any work, switch off the mains 

supply to the appliance.

CAUTION

Do not operate the immersion heater until the 

appliance has been filled with water.

WARNING

When handling the appliance, take appropriate 

precautions for the weight of the appliance. 

Weights can be found in section 3, p5.

CAUTION

Annual maintenance is recommended to be 

carried out by a competent person, see section 

9, page 15.

WARNING 

  This appliance is supplied with a 

factory temperature setting of 54°C for 

optimum energy efficiency. However, in 

some applications to aid in the control of 

legionella it may be necessary to reset 

this to a higher temperature. It is the 

responsibility of the installer and end 

user to ensure that where applicable the 

requirements of the "Approved Code of 

Practice L8: The control of legionella 

bacteria in water systems" are met.

Summary of Contents for Express 50 Litres

























Reviews: