background image

5

Heatilator • ECO-WINS18 • 7065-132D • November 22, 2011

WARRANTY COVERAGE:

•  This warranty only covers HHT appliances that are purchased through an HHT authorized dealer or distributor.  A list of 

HHT authorized dealers is available on th HHT branded websites.

•  This warranty is only valid while the HHT appliance remains at the site of original installation.
•  Contact your installing dealer for warranty service.  If the installing dealer is unable to provide necessary parts, contact 

the nearest HHT authorized dealer or supplier.  Additional service fees may apply if you are seeking warranty service 
from a dealer other than the dealer from whom you originally purchased the product.

•  Check with your dealer in advance for any costs to you when arranging a warranty call.  Travel and shipping charges 

for parts are not covered by this warranty.

WARRANTY EXCLUSIONS:

This warranty does not cover the following:

•  Changes in surface fi nishes as a result of normal use.  As a heating appliance, some changes in color of interior and 

exterior surface fi nishes may occur.  This is not a fl aw and is not covered under warranty.

•  Damage to printed, plated, or enameled surfaces caused by fi ngerprints, accidents, misuse, scratches, melted items, 

or other external sources and residues left on the plated surfaces from the use of abrasive cleaners or polishes.

•  Repair or replacment of parts that are subject to normal wear and tear during the warranty period.  These parts include:  

paint, wood, pellet and coal gaskets; fi rebricks; grates; fl ame guides; light bulbs; batteries and the discoloration of 
glass.

•  Minor expansion, contraction, or movement of certain parts causing noise.  These conditions are normal and com-

plaints related to this noise are not covered by this warranty.

•  Damages resulting from:  (1) failure to install, operate, or maintain the appliance in accordance with the installation 

instructions, operating instructions, and listing agent identifi cation label furnished with the appliance; (2) failure to 
install the appliance in accordance with local building codes; (3) shipping or improper handling; (4) improper operation, 
abuse, misuse, continued operation with damaged, corroded or failed components, accident, or improperly/incorrectly 
performed repairs; (5) environmental conditions, inadequate ventilation, negative pressure, or drafting caused by tightly 
sealed constructions, insuffi cient make-up air supply, or handling devices such as exhaust fans or forced air furnaces 
or other such causes; (6) use of fuels other than those specifi ed in the operating instructions; (7) installation or use of 
components not supplied with the appliance or any other components not expressly authorized and approved by HHT; 
(8) modifi cation of the appliance not expressly authorized and approved by HHT in writing; and/or (9) interruptions or 
fl uctuations of electrical power supply to the appliance.

•  Non-HHT venting components, hearth components or other accessories used in conjunction with the appliance.
•  Any part of a pre-existing fi replace system in which an insert or a decorative gas appliance is installed.
•  HHT’s obligation under this warranty does not extend to the appliances’ capability to heat the desired space.  Informa-

tion is provided to assist the consumer and the dealer in selecting the proper appliance for the application.  Consider-
ation must be given to appliance location and confi guration, environmental conditions, insulation and air tightness of 
the structure.

This warranty is void if:

•  The appliance has been over-fi red or operated in atmospheres contaminated by chlorine, fl uorine, or other damaging 

chemicals.  Overfi ring can be identifi ed by, but not limited to, warped plates or tubes, rust colored cast iron, bubbling, 
cracking and discoloration of steel or enamel fi nishes.

•  The appliance is subjected to prolonged periods of dampness or condensation.
•  There is any damage to the appliance or other components due to water or weather damage which is the result of, but 

not limited to improper chimney or venting installation.

WARRANTY EXCLUSIONS:

•  The owner’s exclusive remedy and HHT’s sole obligation under this warranty, under any other warranty, express or 

implied, or in contract, tort or otherwise, shall be limited to replacement, repair, or refund, as specifi ed above.  In no 
event will HHT be liable for any incidiental or consequential damages caused by defects in the appliance.  Some states 
do not allow exclusions or limitation of incidental or consequential damages, so these limitations may not apply to you.  
This warranty gives you specifi ce rights; you may also have other rights, which vary from state to state.  EXCEPT TO 
THE EXTENT PROVIDED BY LAW, HHT MAKES NO EXPRESS WARRANTIES OTHER THAN THE WARRANTY 
SPECIFIED HEREIN.  THE DURATION OF ANY IMPLIED WARRANTY IS LIMITED TO DURATION OF THE EX-
PRESSED WARRANTY SPECIFIED ABOVE.

Page 2 of 2

7014-212B     1-10-11

Summary of Contents for ECO-WINS18

















































Reviews: