background image

Page 8 of 36

 

101515-0 RMLD MANUAL REV 

F

 

Chapter I

 

RMLD System Specifications

 

Detection Method: 

Tunable Diode Laser Absorption Spectroscopy (TDLAS) 

Measurement Range: 

0 to 99,999 ppm-m 

Sensitivity: 

5 ppm-m at distance from 0 to 50 ft (15 m) 
10 ppm-m or better from 50 to 100 ft (15 to 30 m) 

Detection Distance: 

100 ft (30 m) nominal.  Actual distance may vary due to 
background type and conditions 

Beam Size: 

Conical in shape with a 22” width at 100 ft. (56 cm at 30 m) 

Detection Alarms Modes 

Digital Methane Detection (DMD): 

Audible tone relative to concentration when 

detection threshold exceeded. 

Adjustable Alarm Detection Threshold from 0 to 

255 ppm-m 

Pure Tone: 

Continuous audio tone relative to concentration 

System Fault Warning 

Audible tone and indication on the display 

Self Test & Calibration 

Built-in Self-Test and Calibration function verifies 
operation and adjusts laser wavelength for maximum 
sensitivity.  Test gas cell integrated with carrying case. 

Compliance: 

EMC (EN61000-6-2, EN6100-6-4) Pending 

Laser Eye Safety: 
(CDRH, ANSI and IEC) 

IR Detector Laser: 

Class I 

Green Spotter Laser: 

Class IIIa; Do not stare into beam or view directly 

with optical instruments. 

Display: 

Large easy to read backlit LCD (.75” Numeric) 

Operating Temperature 

0° to 122° F (-17° to 50° C) 

Humidity 

5 to 95 % RH, non-condensing 

Enclosure: 

IP54 (Water splash and Dust resistant) 

Instrument Weight: 

9 lbs  (Transceiver 3 lbs, Controller 6 lbs)  (4 kg; 1.3  kg, 

2.7 kg) 

Carry Case: 

14 lbs; 34” x 9 ½” x 14”  (6.4 kg; 86 cm x 24 cm x 36 cm) 

Power Supply 

Internal rechargeable Li-ion battery 
External Backup Battery pack with 5 C cells (Optional) 

Battery Operating Life 

8 hours at 32° F without backlight on (Internal battery) 

Battery Charger 

External, in-line, 110 – 240 VAC, 50 / 60 hertz universal 
type with charge indicator (8 hours maximum to full charge) 

Shoulder Strap 

Single over the shoulder padded strap 
Ergonomic dual strap and belt system (Optional) 

Summary of Contents for RMLD







































Reviews: