manualshive.com logo in svg

Heatcraft H-IM-QRC, Installation And Operation Manual, Page: 23 / 40

Share
Download
Heatcraft H-IM-QRC Installation And Operation Manual Download Page 23

23

InterLink Replacement Parts List

OPERATIONAL LIMITS

Voltage Range 

18 VAC to 30 VAC

Controlling Box Temp. Range 

-30

°F to 70°F

Temperature Differential 

2°F

Cold Ambient Limits 

Start & operate to -20°F

Table 4. Operational Limits

Commercial Refrigeration Parts

Replacement Parts by

InterLink is your link to a complete line of dependable and certified commercial refrigeration parts, accessories and innovative 
electronic controls for all Heatcraft Refrigeration Products (HRP) brands - including Bohn, Larkin, Climate Control and Chandler. 
At InterLink, we provide our wholesalers with a comprehensive selection of product solutions and innovative technologies for 
the installed customer base. And every product is built to ensure the same high performance standards with which all HRP 
brands are built — backed by a dedicated team to serve every customer need, delivering at the best lead times in the industry.

Visit www.interlinkparts.com or call (800) 686-7278 for more information.

 

PART DESCRIPTION 

PART NUMBER

 

 

** Heatcraft Quick Response Controller Control Board  

28910104

 
 

* Temperature Sensor kit – White Leads  

89904902

 
 Transformers: 
 

 

120/24 volt – 40 VA 

22529601

 

 

240/24 volt – 40 VA 

22529602

  
 

 

Electric Expansion Valve

 

 

E2V11BWAE0  – 3/8" x 3/8"  Conn 

29326101

 

 

E2V24BWAE0  – 3/8" x 3/8"  Conn 

29326201 

 

 

E2V24BSME0  – 5/8" x 5/8"  Conn 

29326401

 

 

E3V45BSME0  – 7/8" x 1-3/8"  Conn 

29326501

 

 

E2V11BWAE0  – 7/8" x 1-3/8"  Conn 

29326601

 

 

Expansion Valve molded connector - 40"  Conn  

22592101

 

 

(Bipolar Valves) 

  

  

 

 

 

Pressure Transducer 

28911201

 

 

 

Pressure Transducer Harness 

22515101   

** 28910104 serves as a replacement part for 28910102
* Only the sensor with white leads is shipped as a service replacement part

Table 3. InterLink Replacement Parts List

Summary of Contents for H-IM-QRC









































Reviews:

No comments