background image

7

Heat & Glo  • REVO-V12, REVO-S21, REVO-H31 Owner’s Manual  •  2273-981  • Rev. G  •  5/14 

WARNING! DO NOT operate 

fi

 replace before read-

ing and understanding operating instructions. 

Failure 

to operate 

fi

 replace according to operating instructions 

could cause 

fi

 re or injury.

Contact your dealer for more information, or visit: www.
hpba.org/safety-information.

To prevent unintended operation when not using your 

fi

 replace for an extended period of time (summer months, 

vacations, trips, etc):
•  Remove batteries from remote controls.
•  Turn off wall controls.
•  Unplug 6 volt adapter plug (IPI) and remove batteries 

on IPI Plus models. 

A. Appliance Safety

General Information 

 

Clear Space

WARNING! DO NOT

 place combustible objects in front 

of the 

fi

 replace or block vent slots.

 

High temperatures 

may start a 

fi

 re. See Figure 3.1.

 Avoid placing candles and other heat-sensitive objects on 
mantel or hearth. Heat may damage these objects.

Figure 3.1  Clear Space

Over Firing

The appliance is considered to be over 

fi

 ring if the 

fl

 ames 

are contacting the top of the 

fi

 rebox.  Call a quali

fi

 ed service 

technician to service the appliance

CLEAR SPACE

3 FT. IN 

FRONT OF 

FIREPLACE

4 IN. MIN.TO 
FINISHED FLOOR

FLOOR CAN BE 

COMBUSTIBLE

 

DO NOT BLOCK 

CONVECTION VENTS

WARNING

A barrier designed to reduce the risk of burns from the 
hot viewing glass is provided with this appliance and 
shall be installed.  DO NOT operate the appliance with 
the barrier removed.  If the barrier becomes damaged, 
the barrier shall be replaced with the manufacturer’s 
barrier for this appliance. 

Contact your dealer or Hearth & Home Technologies if the 
barrier is not present or help is needed to properly install one.

HOT GLASS 

WILL 

          CAUSE BURNS. 

DO NOT

 TOUCH GLASS 

UNTIL  COOLED.

NEVER

  ALLOW CHILDREN

TO TOUCH GLASS.

•  Keep children away.
•  CAREFULLY SUPERVISE children in same room 

as 

fi

 replace.

•  Alert children and adults to hazards of high 

temperatures.

High temperatures may ignite clothing or other 

fl

 ammable materials.

•  Clothing, furniture, draperies, and other 

fl

 ammable 

materials must not be placed on or near the 
appliance.

Young children should be carefully supervised when they 

are in the same room as the appliance.  Toddlers, young 
children and others may be susceptible to accidental 
contact burns.
•  A physical barrier is recommended if there are at risk 

individuals in the house.  

•  To restrict access to a 

fi

 replace or stove, install an 

adjustable safety gate to keep toddlers, young children 
and other at risk individuals out of the room and away 
from hot surfaces.

•  Install a switch lock or a wall/remote control with child 

protection lockout feature.

•  Keep remote controls out of reach of children.
•  Never leave children alone near a hot 

fi

 replace, whether 

operating or cooling down.

•  Teach children to NEVER touch the 

fi

 replace.

•  Consider not using the 

fi

 replace when children will be 

present.

Summary of Contents for REVO-H31

























Reviews: