Heat Transfer TX Series Installation, Operation And Maintenance Manual Download Page 26 | Manualshive

Page: 26 / 33

background image

TX Series Installation, Operation, and Maintenance Manual

Diversified Heat Transfer, Inc.



439 Main Road, Route 202



Towaco, New Jersey 07082

Page

26

of

33

Phone: 800-221-1522



Website: www.dhtnet.com

SECTON 6.3: PARTS AND ACCESSORIES

The following is a list of typical parts that are generally replaceable by personnel trained/certified on
DHT, Inc., TX Series water heaters. The replaceable parts may vary, depending on the unit and the
particular design specifications in which the unit was constructed. If there are questions concerning the
replaceable parts for the unit, refer to the original design specifications, or contact DHT, Inc.

NOTE:

All replacement parts of unit can be ordered directly from your local authorized DHT sales
representative/agent. Please have the unit’s model and serial number available before contacting.

ITEM NO.

PART NO.

QUANTITY

DESCRIPTION

1

RB450-TX-40

1

TX-40 TX SERIES INDIRECT WH

RB450-TX-50

TX-50 TX SERIES INDIRECT WH

RB450-TX-80

TX-80 TX SERIES INDIRECT WH

RB450-TX-110

TX-110 TX SERIES INDIRECT WH

2

MELE-04-0005

1

AQUASTAT (FOR USA ONLY)

MELE-04-0002

AQUASTAT (FOR CANADA ONLY)

3

RB450-WELLS

1

AQUASTAT WELL

4

MPART-E-RV1-0006

1

T&P RELIEF VALVE

5

MPART-E-05-0001

1

DRAIN VALVE

6

RB450-TX-LEGS

3

LEGS

7

RB450-TX-BUSHING

1

S.S. REDUCING BUSHING – 1” x ¾”

(FOR: MODELS TX-40, TX-50 & TX-80)

8

RB450-TX-40-CARTONS

1

CARTONS TX-40

RB450-TX-50-CARTONS

CARTONS TX-50

RB450-TX-80-CARTONS

CARTONS TX-80

RB450-TX-110-CARTONS

CARTONS TX-110

«
...
24
25
26
27
28
...
»

Summary of Contents for TX Series


































Reviews:

No comments

Related manuals for TX Series

Brand: A.O. Smith Pages: 2

Brand: DAB Pages: 13

Brand: Eccotemp Pages: 56

Brand: Quick Pages: 16

Brand: Gardena Pages: 8

Brand: Laser Pages: 4

Brand: Oceanic Pages: 201

Brand: T.I.P. Pages: 24

Brand: Taco Pages: 56

Brand: Taco Pages: 12

Brand: Saxon Pages: 12

ROYTRONIC A Series

Brand: LMI Pages: 36

FLEXFLO A-100NE

Brand: Blue-White Pages: 28

Brand: HELLER Pages: 15

Brand: Argo Pages: 9

Brand: SAMES KREMLIN Pages: 51

FLOOD KING 240V

Brand: U.S. Products Pages: 8

Brand: veito Pages: 24

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands