Heat-N-Glo RHW-44 Installation & Operating Instructions Manual Download Page 24

3-00

24                                                                   33147 Rev A

WARRANTY

FOR HEAT-N-GLO FIREPLACES

The limited warranty will not become effective until you have mailed the completed warranty card to HEAT-N-GLO,

A DIVISION OF HEARTH TECHNOLOGIES INC., 20802 Kensington Blvd., Lakeville, MN 55044.

This card must be mailed within 60 days of the fireplace installation.

Subject to the conditions set forth herein, Heat-N-Glo extends the following limited warranty with respect to your Heat-N-Glo fireplace, excluding
accessories, Chimney components and Glass Doors.

If Heat-N-Glo is satisfied that any part or portion of the fireplace covered by this warranty is defective in material or workmanship under normal
use and service as described in the operating instructions, Heat-N-Glo will take the following actions:

1.

Within the first five (5) years from the date of installation, Heat-N-Glo shall, at its option, replace or repair any 
such defect in material or workmanship, at Heat-N-Glo’s expense.  HEAT-N-GLO SHALL NOT BE RESPONSIBLE FOR 
ANY OTHER LABOR COSTS, OR EXPENSES, INCLUDING INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES.

2.

During the sixth (6th) through the (10th) years after the date of installation, Heat-N-Glo shall supply replacement parts 
or parts at no charge, but SHALL NOT BE RESPONSIBLE FOR ANY LABOR, TRANSPORTATION, OR OTHER INDI-
RECT DAMAGES.

3.

During the eleventh (11th) through the fifteenth (15th) years after date of installation, Heat-N-Glo will send to you, FOB 
its factory, replacement parts (if available) at the current minimum wholesale price, but Heat-N-Glo SHALL NOT BE 
RESPONSIBLE FOR ANY LABOR, TRANSPORTATION OR OTHER INDIRECT DAMAGES.

4.

During the first six (6) months after installation, HEAT-N-GLO shall, at its option, replace or repair the Glass Doors and 
any electrical components, if operation is faulty.  (This does not include Glass panels broken during shipment, misuse or 
careless handling.)  After the first six (6) months, HEAT-N-GLO will sell to you, FOB its factory, replacement parts at the 
current list price, but HEAT-N-GLO  SHALL NOT BE RESPONSIBLE FOR ANY LABOR, TRANSPORTATION OR 
OTHER INDIRECT DAMAGES.  IF GLASS DOORS OTHER THAN FACTORY DOORS ARE USED ALL WARRANTY 
AND LIABILITY ON THE FIREPLACE IS VOIDED.

Heat-N-Glo may discharge its entire warranty liability by refunding the price of the product.

Products made by other manufacturers, sold with the fireplace or thereafter are not covered by this limited warranty.

This limited warranty will be void if the fireplace is not installed according to the installation instructions.  The limited warranty also is void if the
fireplace is not operated, at all times, according to the operating instructions furnished.  The limited warranty will also be void if the fireplace is
removed from the place originally installed.

EXCEPT TO THE EXTENT PROVIDED BY LAW, NO IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR
PURPOSE, AND NO IMPLIED WARRANTIES SHALL APPLY TO THE FIREPLACE AFTER THE ABOVE LIMITED WARRANTY HAS
EXPIRED.

In states that do not allow limitations on how long implied warranty lasts, or do not allow exclusion of indirect damages, those limitations or
exclusions may not apply to you.  You may also have additional rights not covered in this limited warranty.

HEAT-N-GLO reserves the right to make changes at anytime, without notice, in design, material, specifications and prices and the right to dis-
continue styles and products.

UNDERWRITERS LABORATORIES FILE NO. MH5850

Summary of Contents for RHW-44

























Reviews: