Heat Controller A-VMH18DC-1 Service Service Manual Download Page 23 | Manualshive

Page: 23 / 50

background image

23

Heat Controller, Inc.

VMH SerieS

Service Manual

8.5.4 Compressor current limit protection

If the compressor current exceeds the current limit value for 10 seconds, the compressor frequency will be

limited per the table below.

Cooling mode:

Current frequency(Hz)

Current limit value(A)

Frequency limit

COOL_F10

ICOOLLMT6

The compressor frequency will decrease to COOL_F4 and

then run at COOL_F4 for 3 minutes.

After that, the frequency will be adjusted according to the

capacity demand, then rise to the next level up every 3

minutes (When the frequency>COOL_F4 via capacity

demand).

COOL_F9

ICOOLLMT5

COOL_F8

ICOOLLMT4

COOL_F7

ICOOLLMT3

COOL_F6

ICOOLLMT2

COOL_F5

ICOOLLMT1

If the current frequency is lower than COOL_F4, the frequency will not be limited.
After 10s of the compressor start, if the current>ICOOL,the AC will display the failure for 30 seconds and stop. The AC will restart 3

minutes later and re-check.

Heating mode:

Current frequency(Hz)

Current limit value(A)

Frequency limit

HEAT_F12

IHEATLMT8

The compressor frequency will decrease HEAT_F4 and

then run at HEAT_F4 for 3 minutes.

After that, the frequency will be adjusted according to the

capacity demand, then rise to the next level up every 3

minutes (When the frequency>Heat_F4 via capacity

demand).

HEAT_F11

IHEATLMT7

HEAT_F10

IHEATLMT6

HEAT_F9

IHEATLMT5

HEAT_F8

IHEATLMT4

HEAT_F7

IHEATLMT3

HEAT_F6

IHEATLMT2

HEAT_F5

IHEATLMT1

If the current frequency is lower than HEAT_F4, the frequency will not be limited.
After 10s of the compressor start, if the current>IHEAT,the AC will display the failure for 30 seconds and stop. The AC will restart 3

minutes later and re-check.

«
...
21
22
23
24
25
...
»

Summary of Contents for A-VMH18DC-1 Service



















































Reviews:

No comments

Related manuals for A-VMH18DC-1 Service

Brand: Olimpia splendid Pages: 96

Brand: Zibro Pages: 2

Brand: Panasonic Pages: 53

Split Type Room Air Conditioner

Brand: Midea Pages: 14

PrecisionAire 225T Series

Brand: Flanders Pages: 5

WMMS-09C-V2A/B(58) 2

Brand: YMGI Pages: 20

Brand: Electra Pages: 110

WAECO VAS 581 001

Brand: Dometic GROUP Pages: 328

Brand: Momax Pages: 41

Brand: ClimateRight Pages: 10

Brand: Goodman Pages: 14

Brand: Prem-I-Air Pages: 12

Compact i10 VSD

Brand: VelAir Pages: 27

Brand: Gree Pages: 25

Brand: Danby Pages: 20

Dual DC Inverter (4,1 kW)

Brand: MAXA Pages: 43

Brand: Winix Pages: 84

Brand: Daikin Pages: 15

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands