manualshive.com logo in svg

Heat & Glo Soho-N-AU, Installer'S Manual, Page: 27 / 41

Share
Download
Heat & Glo Soho-N-AU Installer'S Manual Download Page 27

Heat & Glo  •  SOHO-N-AU  •  2197-900 Rev. C •  9/09

27

This kit is used in place the logs in a SOHO-N-AU.  Alter-
nate media and refl ective fi rebox liner is provided.

CAUTION! Risk of Cuts, Abrasions or Flying Debris. 
Wear protective gloves and safety glasses during instal-
lation. Sheet metal edges are sharp.

CONTENTS OF KIT: 

• Refl ective Firebox Liner 

 

• Rock Tray

•  Rock or Onyx 

1.  Remove the front and glass from the SOHO-CE and 

set aside.  Remove the logs (if installed) from the unit 
and either discard or save for later use.

2.  Fold down the log locating tabs (if bent up) on the base 

pan so they are parallel with the burner. See Figure 12.7.

3.  Install  the  fi rebox liner by placing it on the base pan 

of the fi replace and sliding it back until it contacts the 
back of the fi replace.  See Figure 12.7.

Figure 12.6

Figure 12.8

4.  Set the rock tray on top of the base pan. See Figure 12.8.

DO NOT INSTALL ROCKS IN THIS AREA

LOCATING TABS

FIREBOX LINER

BASE PAN

Delayed Ignition Risk

•  Do NOT place rocks on burner.

•  Do NOT place rocks in a position that they may 

fall on the burner.

Fireplace will not function properly. 
Delayed ignition may occur.

WARNING

Figure 12.9

5.  Spread the rock or onyx evenly across the rock tray.  

See Figure 12.9.  

DO NOT

 place rocks in burner area 

or in front of pilot burner.

6.  Reinstall the glass frame and front.

ROCK TRAY

FIREBOX LINER

ROCK TRAY

F.  Install Media Rock Kit

Figure 12.7

Summary of Contents for Soho-N-AU










































Reviews:

No comments