Heat & Glo SLR-C (COSMO) Owner'S Manual Download

Page: 46 / 71

Heat & Glo • SLR-C • 2292-900 Rev. H • 2/13

Gas Information

A. Fuel Conversion

• Make sure the appliance is compatible with available gas

types.

• Conversions must be made by a qualified service

technician using Hearth & Home Technologies specifi ed
and approved parts.

B. Gas Pressure

• Optimum appliance performance requires proper input

pressures.

• Gas line sizing requirements will be determined in ANSI

Z223.1 National Fuel Gas Code in the USA and CAN/
CGA B149 in Canada.

• Pressure requirements are:

WARNING! Risk of Fire or Explosion! High pressure
will damage valve. Low pressure may cause explosion.

• Verify inlet pressures. Verify minimum pressures when

other household gas appliances are operating.

• Install regulator upstream of valve if line pressure is

greater than 1/2 psig.

Gas Pressure

Natural Gas

Propane

Minimum inlet pressure

5.0 in. w.c.

11.0 in. w.c.

Maximum inlet pressure

10.0 in. w.c.

13.0 in. w.c.

Manifold pressure

3.5 in. w.c.

10.0 in. w.c.

Fire Risk.

Explosion Hazard.

High pressure will damage valve.

• Disconnect gas supply piping BEFORE

pressure testing gas line at test pressures
above 1/2 psig.

• Close the manual shutoff valve BEFORE

pressure testing gas line at test pressures
equal to or less than 1/2 psig.

WARNING

Note:

This appliance does include a manual gas shutoff valve

that is located in the valve compartment. This manual gas
shutoff valve is accessible for service by removing the base
pan, burner assembly and valve plate. See Figure 11.1.

The lower access cover panel is removable if fi nishing
material has not been previously installed.

Figure 11.1 Cover Tray Removal

MEDIA TRAY/BASE PAN
ASSEMBLY SCREWS

PILOT BRACKET SCREWS

Figure 11.2. Remove Valve Plate Screws

3. Set the valve bracket on the front lip of the fi rebox bot-

tom. Turn “off” the ball valve. Disconnect gas valve
from the gas fl ex ball valve assembly at the pressure
fi tting. See Figure 11.4.

Figure 11.3. Remove Valve Plate

Access Through the Valve Assembly

The lower access cover panel is removable if fi nishing
material has not been previously installed.

Remove media tray, base pan and burner assembly.

To access components:

1. Remove eleven screws around perimeter of valve

plate that secure valve plate to the fi rebox bottom.
See Figure 11.2.

2. Lift the valve plate from the back so that the gas valve

can clear the valve plate hole in the bottom the fi rebox.
See Figure 11.3.

Summary of Contents for SLR-C (COSMO)








































































Search results

Summary of Contents for SLR-C (COSMO)

Reviews:

Related manuals for SLR-C (COSMO)

Brands by name

Popular brands

Heat & Glo SLR-C (COSMO), Owner'S Manual

Search results

Summary of Contents for SLR-C (COSMO)

Reviews:

Related manuals for SLR-C (COSMO)

Brands by name

Popular brands