Heat & Glo SL-550TR-D Owner'S Manual Download | Manualshive

Page: 22 / 45

background image

Heat & Glo • SL-550 / 750 / 950TR-D • 2044-985 Rev. J • 6/06

22

!

Step 3. Installing the Vent System

A. Vent System Approvals

These models have vent starting collars on both the top
and the back of the unit. Depending upon the installation,
decide which ONE set of starting collars will be used to
attach the vent system. The starting collar sealing cap must
remain on the starting collar NOT used.

These models use SL-D-series, direct vent components
when using the

TOP

vent collars. This pipe is tested and

listed as an approved component of the appliance. The pipe
is tested to be run inside an enclosed wall. There is no
requirement for inspection openings at each joint within the
wall. There is no required pitch for horizontal vent runs.

These models also use DVP-series direct vent components
when using the

REAR

vent collars.

The flame and ember appearance may vary based on the
type of fuel burned and the venting configuration used.

WARNING: YOU MUST NOT MIX DVP-SERIES
AND SL D-SERIES COMPONENTS IN ANY VENT
SYSTEM CONFIGURATION.

Identifying Vent Components

Approved vent system components are labeled for identifi-
cation.

NO OTHER VENTING SYSTEMS OR COMPO-

NENTS MAY BE USED

. Detailed installation instructions

are included with each vent termination kit and should be
used in conjunction with this

Owner's Manual

. Figure 8

shows vent system components and terminations.

The vent systems installed on this gas appliance may in-
clude one, two, or three 90°

elbow assemblies. The rela-

tionships of vertical rise to horizontal run in vent configura-
tions using 90° elbows

MUST BE

strictly adhered to. The

rise to run relationships are shown in the venting drawings
and tables. Refer to the diagrams on the next several pages.

NOTE: Two 45° elbows may be used in place of one
90° elbow. Maximum and minimum rise to run ratios
must always be maintained in the vent system when
using 45° elbows.

Figure 8.

Vent System Components and Termination Kits

Vent System Termination Kits

Vent System Components

HORIZONTAL

TERMINATION

WALL

FIRESTOP

90 DEGREE
ELBOW

VERTICAL
TERMINATION

STORM COLLAR

ROOF FLASHING

HORIZONTAL PIPE
SUPPORT

PIPE LENGTH

WALL BRACKET

CEILING
FIRESTOP

SLK-991DA

SLK-01TRD

DVP-TVHW

SL D-SERIES

DVP-SERIES

(SL-Series)

(SL-Series)

DVP-TRAP

DVP-TB1

PVK-80

SLK-SNKD

SL-FLEX2-01TRF

(Required
to have a
minimum of 3
feet of vertical
in the vent
system)

(There MUST be a 25%
reduction in total H when
using the snorkel cap except
when using the simple up and
out installation (see Fig. 9)

For use with DVP venting.
No adapters.
Use only with IPI models.

SERIES

SLK-01TRF*

*For use with flex

vent only.

«
...
20
21
22
23
24
...
»

Summary of Contents for SL-550TR-D














































Reviews:

No comments

Related manuals for SL-550TR-D

Brand: Jetmaster Pages: 13

Brand: Jetmaster Pages: 17

Brand: RAIS Pages: 34

Brand: M Pages: 4

Brand: United States Stove Company Pages: 16

Brand: Napoleon Pages: 4

Brand: Napoleon Pages: 4

Brand: Napoleon Pages: 2

Brand: barbas Pages: 32

Brand: barbas Pages: 48

ST. CROIX HD WT17YL

Brand: Backyard Creations Pages: 13

Brand: Panadero Pages: 36

Brand: Desa Pages: 44

Stamford Firebowl

Brand: La Hacienda Pages: 4

Brand: Uniflame Pages: 8

Brand: Xaralyn Pages: 10

Brand: Valor Pages: 24

Brand: M Design Pages: 14

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands