Heat & Glo EXCLAIM-50 Owner'S Manual Download

Page: 5 / 52

Listing and Code Approvals

NOTICE:

This fireplace is tested and approved as a

decorative

replace. It should not be factored as a primary

heat source in residential heating calculations.

WARNING! Risk of Fire!

Hearth & Home Technologies

disclaims any responsibility for, and the warranty and
agency listing will be voided by the following actions.

DO NOT:

• install or operate damaged

replace

•

modify

replace

• install other than as instructed by Hearth & Home

Technologies

•

operate

the

replace without fully assembling all

components

•

over

• install an unvented gas log set

• install any component not approved by Hearth & Home
Technologies

• install parts or components not Listed or approved

Improper installation, adjustment, alteration, service or
maintenance can cause injury or property damage. For
assistance or additional information, consult a quali

installer, service agency or your dealer.

B. Non-Combustible Materials

• Materials which will not ignite and burn, composed of

any combination of the following:
- Steel

Iron

- Brick

- Tile

- Concrete

- Slate

- Glass

- Plasters

• Materials reported as passing

ASTM E 136, Standard

Test Method for Behavior of Metals, in a Vertical Tube
Furnace at 750° C

C. Combustible Materials

• Materials made of or surfaced with any of the following

materials:
- Wood

- Compressed

paper

- Plant

bers

- Plastic

• Any material that can ignite and burn;

ame proofed or

not, plastered or un-plastered

Heat & Glo • EXCLAIM-50 • 4013-041 • Rev T • 08/08

A. Appliance Certi

cation

This

replace system has been tested and listed in accor-

dance with UL 127 standards by Underwriters Laborato-
ries Inc. for installation and operation in the United States.

This

replace may be installed in sleeping rooms EX-

CEPT in manufactured homes. If installed with a gas log
set, provisions for the National Fuel Gas Code must be
met.

This

replace has been tested and listed for use with the

optional components speci

ed in this manual. These op-

tional components may be purchased separately and in-
stalled at a later date. Installation of an outside air kit will
require signi

cant reconstruction and is best if installed at

the time of

replace installation.

Heat & Glo is a registered trademark of Hearth & Home
Technologies Inc.

Summary of Contents for EXCLAIM-50





















































Search results

Summary of Contents for EXCLAIM-50

Reviews:

Related manuals for EXCLAIM-50

Brands by name

Popular brands

Heat & Glo EXCLAIM-50, Owner'S Manual

Search results

Summary of Contents for EXCLAIM-50

Reviews:

Related manuals for EXCLAIM-50

Brands by name

Popular brands