Heat & Glo EXCLAIM-50 Owner'S Manual Download | Manualshive

Page: 20 / 52

background image

20

7

7

Installation of Fireplace

CAUTION! Risk of Cuts/Abrasions.

Wear protective

gloves and safety glasses during installation. Sheet metal
edges are sharp.

A. Things to Consider

•  Location of chimney air kit
•  Location(s) of outside air kits
•  Electrical connections and/or wall switch
•  Gas line piping

Figure 7.1 Unpack Back Refractory

Figure 7.2 Bend Refractory Brackets Back Down

B. Unpack the Refractory & Fireplace

• Remove back refractory from outside of

fi

replace by

bending tabs up and lifting refractory out of brackets.
See Figure 7.1.

• Bend tabs back down out of the way. See Figure 7.2.
• Do not remove screws or refractory brackets from

fi

replace. If refractory brackets must be removed,

fi

ll

holes in outer shell with screws.

• Repeat this process to remove side refractories.

Figure 7.4 Shipping Spacers

Figure 7.3 Remove Screen Rods

•

Remove hearth stone by removing three corrugated
shipping spacers (Figure 7.4). Lift hearth stone out of

fi

replace. See Figure 7.5.

Figure 7.5 Lifting Out Hearth Stone

• Remove screens by removing screw from end of each

screen rod.

Figure 7.6 Removing Shipping Brackets

• Remove

fi

replace from pallet:

- Remove screws from shipping brackets and pallet

(Figure 7.6),

- Replace screws removed from

fi

replace.

- Brackets can be used to anchor fireplace in

position.

Heat & Glo • EXCLAIM-50 • 4013-041 • Rev T • 08/08

«
...
18
19
20
21
22
...
»

Summary of Contents for EXCLAIM-50





















































Reviews:

No comments

Related manuals for EXCLAIM-50

Brand: barbas Pages: 60

CROSSOVER CO10-102

Brand: Magma Pages: 22

Brand: komodo Pages: 40

Duraflame DFI030ARU

Brand: Twin-Star International Pages: 26

Brand: Napoleon Pages: 16

Black Beauty Slimline

Brand: Valor Pages: 47

Brand: Miles Industries Pages: 32

Brand: BCP Pages: 16

Brand: KEKAI Pages: 18

Brand: Harman Pages: 28

Brand: Heat-N-Glo Pages: 37

BEDFORD A Series

Brand: Pacific energy Pages: 44

Brand: Backyard Creations Pages: 6

Brand: Wamsler Pages: 84

PARAGON FOCUS 18 HE

Brand: Charlton & Jenrick Pages: 32

Personal Fireplace Heater YH-28

Brand: Tristar Products Pages: 8

Brand: Bond Pages: 16

Brand: Bond Pages: 36

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands