Heat & Glo EXCLAIM-50 Owner'S Manual Download

Page: 26 / 52

A. Chimney Requirements

Measure vertical distances from the base of the

replace

as shown in Figure 8.2.

6 ft (1.83 m) max.
unsupported run

20 ft (6.10 m) max.
pipe between an
offset & return

Ceiling Firestop

35 ft (10.67 m)

max. straight

unsupported

chimney height

20.5 ft (6.25 m) min. height/single offset-return

24 ft. (7.32 m) min. height/double offset-return

90 ft (27.43 m) max. height

6 ft (1.83 m) max.
unsupported chimney
above roof

68-1/8 in.

(1730 mm)

Effective Height

(bottom of fireplace

to top of starter collar)

Gas

Knockout

Figure 8.2 Chimney Requirements

Table 8.1

• Minimum overall straight height

20 ft

(6.1 m)

• Minimum height with offset/return

20.5 ft

(6.25 m)

• Maximum height

90 ft (27.43 m)

• Maximum chimney length between an offset

and return

20 ft

(6.1 m)

• Maximum distance between chimney

stabilizers

35 ft (10.67 m)

• Double offset/return minimum height

24 ft

(7.32 m)

• Maximum unsupported chimney length

between the offset and return

6 ft

(1.83 m)

• Maximum unsupported chimney height above

the

replace

35 ft (10.67 m)

• Maximum unsupported chimney above roof

6 ft

(1.83 m)

WARNING! Risk of Fire!

You must maintain 2 in. (51

mm) air space clearance to insulation and other combus-
tible materials around the chimney system. Failure to do
so may cause overheating and

re.

Determine the chimney components needed to complete
your particular installation:

• Measure the total vertical height of the fireplace

installation from the base of the

replace assembly to

the approximate location of the bottom of the termination
cap.

• Subtract the effective height of the

replace assembly

(see Figure 8.2) from the total vertical height to determine
the overall height of the chimney installation.

• Create a schematic for your application similar to Figure

8.2 showing components required (referring to Table
8.1). Figure 8.1 identi

es those components and where

used.

• Install a ceiling

restop whenever the chimney penetrates

oor/ceiling.

NOTICE:

A maximum of two pairs of offsets and returns

may be used.

CAUTION! Risk of Fire and/or Asphyxiation! DO

NOT

connect this

replace to a chimney

ue servicing

another appliance.

DO NOT

connect to any air distribu-

tion duct or system. These actions could cause over-
heating/

re in the chimney

ue, or release of exhaust

fumes into the living areas.

Heat & Glo • EXCLAIM-50 • 4013-041 • Rev T • 08/08

HEIGHT OF CHIMNEY COMPONENTS

in.

Chimney Stabilizer

SL11

4-3/4

121

Ceiling Firestops

FS538

FS540

Offsets/Returns

SL1130

457

Roof Flashing

RF570

RF571

Chimney Sections*

SL1106

4-3/4

121

SL1112

10-3/4

273

SL1118

16-3/4

425

SL1136

34-3/4

883

SL1148

46-3/4

1187

* Dimensions re

ect effective height.

Summary of Contents for EXCLAIM-50





















































Search results

Summary of Contents for EXCLAIM-50

Reviews:

Related manuals for EXCLAIM-50

Brands by name

Popular brands

Heat & Glo EXCLAIM-50, Owner'S Manual

Search results

Summary of Contents for EXCLAIM-50

Reviews:

Related manuals for EXCLAIM-50

Brands by name

Popular brands