Heat & Glo EXCLAIM-50 Owner'S Manual Download

Page: 1 / 52

Owner’s Manual

Installation and Operation

Models:
EXCLAIM-50

Wood Burning Fireplace

DO NOT DISCARD THIS MANUAL

NOTICE

• Important

operating

a n d m a i n t e n a n c e
instructions included.

• Leave this manual with

party responsible for
use and operation.

• Read,

understand

and follow these
instructions for safe
i n s t a l l a t i o n a n d
operation.

NOT

DISCARD

Installation and service of this

replace

should be performed by quali

ed personnel.

Hearth & Home Technologies suggests NFI
certi

ed or factory-trained professionals, or

technicians supervised by an
NFI certi

ed professional.

Fire Risk

• For use with solid wood fuel or decorative

gas appliance only.

•

DO NOT

install unvented gas logs.

WARNING

If the information in these instruc-
tions is not followed exactly, a

re may result causing property

damage, personal injury, or death.

• Do not store or use gasoline or other

am-

mable vapors and liquids in the vicinity of

this or any other appliance.

• Do not over

re. Over

ring will void your

warranty.

• Comply with all minimum clearances to

combustibles as speci

ed. Failure to

comply may cause house

re.

WARNING

Hot screen/mesh and glass doors will cause burns.

•

DO NOT

touch screen/mesh or glass doors until

cooled

• NEVER allow children to touch screen/mesh or glass

doors

• Keep children away
• CAREFULLY SUPERVISE children in same room as

replace.

• Alert children and adults to hazards of high

temperatures.

High temperatures may ignite clothing or other

ammable materials.

• Keep clothing, furniture, draperies and other

ammable materials away.

HOT SURFACES!

Screen/mesh, glass doors
and other surfaces are hot
during operation AND cool
down.

Heat & Glo • EXCLAIM-50 • 4013-041 • Rev T • 08/08

Summary of Contents for EXCLAIM-50





















































Search results

Summary of Contents for EXCLAIM-50

Reviews:

Related manuals for EXCLAIM-50

Brands by name

Popular brands

Heat & Glo EXCLAIM-50, Owner'S Manual

Search results

Summary of Contents for EXCLAIM-50

Reviews:

Related manuals for EXCLAIM-50

Brands by name

Popular brands