manualshive.com logo in svg

Heartland 3400, User Manual, Page: 9 / 21

Share
Download
Heartland 3400 User Manual Download Page 9

9

Residential Wall Mount Hood

3. Hood Installation

(3 choices depending on framing choice)

A. Back Installation

Note:  Use only keyholes and holes shown in
black, as illustrated below, and on the
sketches provided.

Keyholes provided for easy installa-
tion.  These should all be used.

Optional holes provided only for
stronger installation when necessary.

1.

Mark the location of the 5 installation

screws (keyholes) on the wood panel.

2.

Do not tighten the installation screws

(3/4") down. The hood can be placed on
them before tightening.

3.

Insert the electrical wire (power supply)

in the hole, ensuring the wire clamp
connector is in place.

4.

Insert the screw heads inside the key-

holes of the hood.

5.

Move down the hood and insert the

screws into the slot of the keyholes.

6.

Tighten the five screws to attach the

hood firmly on the wood panel.

7.

Install (only if necessary) 2 or 4 addi-

tional screws at the locations shown on
the sketch. The numbers of additional
screws depend on the size of the hood.

FR O N T VIEW

all other m odels

FR O N T VIEW

30"

3 /4 "

1 -1 /4 "

1 -1 /4 "

1 3 -5 /8 "

3 /4 "

1 -1 /4 "

1 -1 /4 "

1 3 -5 /8 "

6

4

3

wire clamp
connector

Summary of Contents for 3400






















Reviews:

No comments