Heartland 16826 Assembly Manual Download Page 3

Page: 3 / 71

- CUSTOMER SERVICE -

Call: 1-

800-577-9663

email: [email protected]

BEFORE YOU BEGIN

IMPORTANT!

READ INSTRUCTIONS THOROUGHLY PRIOR TO BEGINNING ASSEMBLY.

• BUILDING RESTRICTIONS AND APPROVALS

Be sure to check with local building department and homeowners association for specific restrictions and/ or requirements before building.

• ENGINEERED DRAWINGS

Contact our Customer Service Team if engineered drawings are needed to pull local permits.

• SURFACE PREPARATION

To ensure proper assembly you must build your shed on a level surface. Recommended methods and materials to level your shed are

listed on page 7.

• CHECK ALL PARTS

Inventory all parts listed on pages 4 - 6. Contact our Customer Service Team if any parts are missing or damaged.

• ADDITIONAL MATERIALS

You will need additional materials to complete your shed. See page 3 for required and optional materials and quantities.

05/18/2015

KEEP THIS MANUAL FOR FUTURE REFERENCE

ACTUAL FLOOR SIZE IS 144" x 90" (365,8 x 228,6 cm)

16826

METROPOLITAN 12' x 7'-6" (365,8 x 228,6 cm)

ASSEMBLY MANUAL

A Backyard Products Company

Summary of Contents for 16826








































































Search results

Summary of Contents for 16826

Reviews:

Related manuals for 16826

Brands by name

Popular brands

Heartland 16826, Assembly Manual

Search results

Summary of Contents for 16826

Reviews:

Related manuals for 16826

Brands by name

Popular brands