background image

Hearthstone Quality Home Heating Products, Inc. 

Bristol DX Model 8762 

 

 

 

12

Specifications 

L

ISTED

:

 

Gas-Fired Direct-Vent Fireplace Heater 

Model: 

Bristol Direct-Vent Gas Fireplace 

Heater (8762) 

Testing Agency: 

Intertek Testing Services 

NA, Inc. (ITS) 

Tested to:

 ANSI Z21.88-09, CSA 2.33-09, 

CAN/CGA2.17-M91 
Certified for Canada, CSA P.4.1-02 
Approved for Mobile Home Installation (see 
page 7) 

Certified for use by: 

Board of State Examiners of Plumbers & Gasfitters 
100 Cambridge Street, Room 1511 
Boston, MA  02202 
www.mass.gov 

 

 

 

 

 

Figure 9 - Model 8762 Dimensions (

Inches

Specification NG

LP 

INPUT RATING (Btu/hr) 0-2000 ft (0-610 m) 

36,000 

33,000 

INPUT RATING (Btu/hr) 2000-4500 ft (610-1370 m) 

35,000 

30,000 

MAXIMUM OUTPUT (Btu/hr) 0-2000 ft (0-610 m) 

28,200 

26,200 

MINIMUM INPUT (btu/hr) 0-2000 ft (0-610 m) 

16,000 

10,000 

ORIFICE SIZE (DMS) 0-2000 ft (0-610 m (front/rear)) 

43/46 

54/57 

ORIFICE SIZE (DMS) 2000-4500 ft (610-1370 m (front/rear)) 

43/47 

55/59 

MANIFOLD PRESSURE - (in. W.c./kpa) 3.5/0.87 

10.0/2.48 

MANIFOLD PRESSURE - Low setting (in. W.c./kpa) 

1.1/.027 

6.4/1.59 

INLET PRESSURE - MINIMUM (in.w.c./kpa) 5.0/1.25 

12.0/2.99 

INLET PRESSURE – MAXIMUM (in. w.c./kpa) 7.0/1.74 

13/3.22 

Summary of Contents for Bristol DX 8762










































Reviews: