background image

3

PRODUCT FEATURES

SAFETY  DEVICE

A  standard  requirement for all vent-free  room
heaters.  This heater has a pilot  with  an  Oxygen
Depletion  Sensor(ODS)  safety  shutoff  system.
The ODS/pilot  shuts  off  the heater  if  there  is
not  enough  fresh  air.

PIEZO  IGNITION  SYSTEM

This  heater  is  equipped  with  a  piezo  ignitor.
This  system  requires  no  matches, batteries, or
other  sources  to  light  heater.

THERMOSTATIC  HEAT CONTROL
ON THERMOSTAT   MODELS

These    heaters    have    a    control    valve    with    a
thermostat    sensing    bulb.  This    results    in    the
greatest    heater    comfort    and    may    result    in
lower  gas  bills.

LOCAL  CODES

Install  and  use  heater  with  care. Follow  all  local
codes. In  the  absence  of  local  codes, use   the
latest  edition  of  

National  Fuel  Gas  Code  ANSZ223.1,

also  known  as  NFPA  54*.
*Available  from :
        American  National  Standards Institute, Inc.

1430  Broadway

New York, NY 10018

National  Fire  Protection  Association, Inc.

Batterymarch  Park

Quincy, MA  02269

QUALIFIED  INSTALLING  AGENCY

Installation    and   replacement   of  gas   piping,   gas
utilization  equipment  or  accessories  and  repair
and servicing  of equipment  shall be  performed  only
by  a qualified  agency.  The  term  “qualified  agency”
means any  individual,  firm ,  corporation,  or  com-
pany   that  either   in   person   or   through  a   repre-
sentative  is engaged  in  and  is  responsible   for  (a)
the  installation, testing, or replacement of gas piping
or (b)  the connection,  installation,  testing,  repair,  or
servicing  of  equipment ; that  is  experienced  in  such
work;  that is  familiar  with  all  precautions  required,
and  that  has complied with all the requirements of
the authority having  jurisdiction.

State of Massachsetts

:  The  installation must  be

made  by  a  licensed  plumber  or  gas  fitter in  the
Commonwealth  of  Massachusetts .
Sellers  of  unvented  propane  or  natural  gas-fired
supplemental  room  heaters  shall  provide  to  each
purchaser a copy  of  527 CMR 30 upon  sale  of  the
unit

.

In the state of Massachusetts, unvented  propane or

nature gas-fired space heaters shall be prohibited in

bedrooms and bathrooms.

UNPACKING

1.   Remove  heater  from  carton.
2.  Remove  all  protective   packaging  applied  to

      heater  for  shipment.
3.   Check  heater  for  any  shipping  damage.  If  heater
     is damaged, promptly  inform  dealer  where  you
      bought  heater.

Figure1-Vent-Free  Propane/LP  Gas  Heater

WAT E R   VA P O R :   A  B Y- P R O D U C T   O F   U N V E N T E D   R O O M   H E AT E R S

Water vapor is a by-product of gas combustion. An
unvented room heater produces approximately one
(1) ounce (30ml) of water for every 1,000 BTU’s
 (.3KW’s) of gas input per hour.
Unvented room heaters are recommended as supple-
mental heat (a room) rather than a primary heat
source (an entire house). In most supplemental heat
applications, the water vapor does not create a
problem. In most applications, the water vapor en-
hances the low humidity atmosphere experienced
during cold weather.

Lower

Front

Panel

Heater

Cabinet

Control

Knob

Grill

Burners

Ignitor

Button

The following steps will help insure that water vapor
does not become a problem.
1. Be sure the heater is sized properly for the
application, including ample combustion air and
circulation air.
2. If  high humidity is experienced, a dehumidifier
may be used to help lower the water vapor content
of the air.
3. Do not use an unvented room heater as the
primary heat source.

Summary of Contents for HB06ML-1

























Reviews: