Hearth and Home Technologies Quadra-Fire CB1200M-MBK, Owner'S Manual

Page: 13 / 40

13 January 28, 2019 7014-259E
CB1200 FREESTANDING
Figure 13.1
O. Thermostat Setup Options
Setup options for how the thermostat will function are
performed using a menu on the display screen.
TO ACCESS THE SETUP MENU:
Move the System Mode Switch into the OFF position,
and then hold down the COPY button for approximately 5
seconds until the screen changes. The menu will always
start with item #01, and is advanced to each following item
by a single press of the NEXT button. The options for each
item are changed using the UP or DOWN buttons.
ITEM #01 (CLK = CLOCK FORMAT):
• 12Hr, default: This displays the clock times using
standard AM and PM values.
• 24Hr: This displays the clock times using the military-
time format (example 22:00 hours, without using AM or
PM).
ITEM #02 (TMP = TEMPERATURE SCALE):
• F, default: Shows all temperature values in Fahrenheit.
• C: Shows all temperature values Celsius.
ITEM #03 (PROGRAMMING STYLE):
• 7 Day, default: This style uses a separate program
routine for each of the 7 days in the week.
• 5/2 Day: This style uses a weekday program routine for
Monday, Tuesday, Wednesday, Thursday, Friday, and
a separate weekend program routine for Saturday and
Sunday.
• Manual Non-Programmable: In this setting, there are
no program routines for the thermostat to follow and
the temperature control will be set only by the UP and
DOWN buttons on the front panel.
ITEM #04 (PERD = EVENT OR PERIOD QUANTITY):
• 4P, default: Thermostat uses four Events per day
(called MORN, DAY, EVE , and NITE).
• 2P: The thermostat uses two Events per day (called
DAY and NITE).
NOTE:
Event or Period Quantity feature is not accessible
during Manual Non-Programmable mode.
ITEM #07 (DLAY = DELAY TIME):
• 5, default: Thermostat waits 5 minutes before turning
the system back on after it was last run. This internal
delay prevents the appliance from turning on too
quickly after shutting down. The 5 minute setting is fine
for most applications.
• 2: Same operation as above but reduced to 2 minutes
between state changes.
NOTE:
This delay does not
happen when the thermostat is manually turned up and
down.
ITEM #08 (TEMPERATURE DIFFERENTIAL):
• The thermostat works by turning your heating system
on and off whenever the room temperature varies
from the desired set-point temperature.
• Use the UP/DOWN buttons to change the number
value between 1 and 9. Generally your system
should cycle on about 3 to 6 times per hour. A smaller
differential number makes the system cycle more
frequently, so the room temperature is more precise
and constant. A larger differential number will make
the system remain on for a longer duration each time
and decreases the number of cycles per hour.
• Default is set to 4.
Event Time Temperature
MORN 6:00 AM 70°F (21°C)
DAY 8:00 AM 62°F (17°C)
EVE 6:00 PM 70°F (21°C)
NITE 10:00 PM 62°F (17°C)
P. Thermostat Operation Instructions
SET DAY AND TIME:
Place the SET switch into the DAY/TIME position. With
the day flashing press UP or DOWN to set the day
or the week. Press NEXT and the clock time will start
flashing. Use UP or DOWN to set the time; verify the AM/
PM indicator is correct. Return the SET switch to RUN
position when finished.
HEATING:
Basic operation of the thermostat can be obtained with
the SET switch in the RUN position. The temperature
can be adjusted using the UP and DOWN buttons.
When the thermostat is first powered on, it will follow a
default temperature routine that is preset from the factory
(Figure 13.1) .
LCD DISPLAY BACKLIGHT:
The display screen is lighted to assist viewing at nighttime,
or in locations with low light levels. Press any button on the
front panel to activate the approximate 10 second backlight.
TEMPERATURE OVERRIDE:
While thermostat is in RUN mode, the set temperature
can be temporarily changed by pressing UP or DOWN.
The temporarily changed set temperature will return to the
programmed value stored in memory when start time of
the next upcoming scheduled event is reached (MORN,
DAY, EVE, OR NITE). While the temporary changed set
temperature is in effect, the word OVERRIDE will be shown
on the display screen. To cancel, move TEMPERATURE
switch to OFF and back to HEAT again.