Hearth and Home Technologies 350TRSI-AUF Owner'S Manual Download Page 58 | Manualshive

Page: 58 / 79

background image

Heat & Glo • 350TRSI-AUF, 350TRSILP-AUF • 2089-980 Rev. C • 10/10

58

FIREPLACE STATUS

THERMOSTAT

THERMOSTAT DESIRED
TEMP SETTING

FLAME HEIGHT

FAN SPEED

ADJUSTABLE
AUXILIARY

ADJUSTABLE
OUTPUT (ON/OFF)

TIMER DISPLAY/FUNCTION

ROOM TEMP
DISPLAY

FUNCTION LEVEL
INDICATOR

LOW BATTERY
INDICATOR

TRANSMISSION
INDICATOR

CHILD LOCK
INDICATOR

Function Buttons

Use POWER button to turn the unit on and off.

Use MENU button to display the menu functions.
Only functions that can be activated will be
displayed.

For example: Flame Height will not

be displayed when the remote status is OFF.

Use the SELECT button to select the current
feature.

Use the UP and DOWN arrows to toggle
through the menu functions and value selec-
tions in the submenus.

Idle When Remote is in ON Mode

The  remote  control  will  go  into  an  idle  mode  if  no  but-
tons  are  pressed  within  5  seconds.  Press  any  button  to
resume  full  functionality.  In  idle  mode  only  active  func-
tions will show on the screen.

Standby mode

The remote control will go into a standby mode if no but-
tons are pressed within 5 minutes. Press the POWER
button to reactivate the remote control to ON mode. Ac-
tive functions will be displayed

Menu

Select

V

V

Display Screen

Figure 12.12 RC300AU Display Screen

«
...
56
57
58
59
60
...
»

Summary of Contents for 350TRSI-AUF
















































































Reviews:

No comments

Related manuals for 350TRSI-AUF

Brand: Vanguard Pages: 30

Brand: Desa Pages: 4

BAYPORT-41 GLASS

Brand: kozy heat Pages: 49

Brand: RealFlame Pages: 38

Brand: HAMPTON BAY Pages: 36

Brand: Be Modern Pages: 8

Brand: Majestic Pages: 20

Brand: Olmo Pages: 8

Brand: Dimplex Pages: 22

Brand: Valor Pages: 16

Brand: Napoleon Pages: 52

Brand: Nordpeis Pages: 72

Brand: Superior Pages: 20

New York Corner

Brand: Nordpeis Pages: 20

Brand: Enviro Pages: 56

Brand: Glen Dimplex Pages: 5

Brand: JC BORDELET Pages: 15

Brand: Design Dynamics Pages: 44

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands