Hearth and Home Technologies 350TRSI-AUF Owner'S Manual Download Page 57 | Manualshive

Page: 57 / 79

background image

57

Heat & Glo • 350TRSI-AUF, 350TRSILP-AUF • 2089-980 Rev. C • 10/10

Figure 12.8 Mounting Remote Control Housing

AUX300CE Module Installation

• Insert the 4 hole harness from the AUX300CE module into

the 4 pin plug on the control module. See Figure 12.9.

Fan Installation

• Insert the 3 prong plug from the fan into the receptacle

located in the AUX300CE module. See Figure 12.10.

• Insert 3 prong plug from AUX300CE module into REM/

AUX receptacle of fi replace junction box.

Figure 12.10 Plug Fan into AUX300CE Module

Figure 12.9 AUX 300 module installation

CONTROL MODULE

AUX 300CE

CABLE

AUX 300

MODULE

AUX 1:

3 steps, HIGH,

MED and LOW

AUX 2:

ON/OFF

3 PRONG PLUG (FAN):

3 steps, timer based,

7 min. ON, 12 min. OFF

FAN CORD

Figure 12.11 Programming RC300AU

Programming the RC300AU to the Control Module

CAUTION! Risk of burns!

DO NOT program the remote

control to the control module when fi replace is hot.

• Verify the ON/OFF/REMOTE switch is in the REMOTE

position. Green LED light will blink three times and the
control module will beep once 5 seconds later when
ready. See Figure 7.

• Using a small item (such as a paper clip) press and

release the LEARN button located near the ON/OFF/
REMOTE switch. See Figure 12.11.

• Control module will beep once and LED will blink green

for 10 seconds.

• While the LED is blinking, press the POWER button on

the remote control. A double beep will come out of the
control module to indicate that it has been programmed
successfully.

NOTICE:

Up to three remote controls can be programmed

into the control module. Simply press a button on the other
remote controls during the 10 second programming process
to add another remote into the system. It is recommended
to program only one RC300AU remote control.

To clear memory in the control module, use a small item
(such as a paper clip) to press and release the LEARN
button. Control module will beep once and LED will blink
green for 10 seconds

DO NOT

press any buttons on the

remote during the ten seconds that the green LED blinks.
The memory will be cleared. Note that the RC300AU will
not be programmed if it’s in STANDBY mode. Press the
ON/OFF button twice to switch to IDLE mode.

REMOTE POSITION

LEARN BUTTON

!

«
...
55
56
57
58
59
...
»

Summary of Contents for 350TRSI-AUF
















































































Reviews:

No comments

Related manuals for 350TRSI-AUF

Brand: Valor Pages: 6

Brand: Harman Pages: 10

Brand: Duraflame Pages: 8

Brand: JAYLINE Pages: 17

Brand: decorflame Pages: 21

Brand: Napoleon Pages: 44

Brand: iKayaa Pages: 2

Brand: HPC Pages: 10

Brand: Travis Industries Pages: 7

Brand: Qindao Hichanse Group Pages: 16

Brand: La Hacienda Pages: 4

Brand: M Design Pages: 2

Brand: Solution FIres Pages: 24

Brand: Kooper Pages: 12

Brand: Camina & Schmid Pages: 40

Brand: Piazzetta Pages: 60

Crea7ion EvoPlus Thales

Brand: GlammFire Pages: 20

Brand: Home Decorators Collection Pages: 41

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands