manualshive.com logo in svg

HCT epc, User Manual, Page: 35 / 41

Share
Download
HCT epc User Manual Download Page 35

 

 

023-00354-Rev1.4      evc/epc 

User 

Manual 

    

 

Copyright © High Country Tek, Inc. – 2013 

 

35

 

evc/epc

 

Controller

  

With

 

SAE

 

J1939

 

Interface

 

SAE J1939 CAN Bus 

 

The evc/epc can be controlled by messages received over the SAE J1939 Bus. 

The EEC1 (PGN: 61444 SA: 0) engine RPM (SPN: 190) can be monitored for use in anti-stall and closed 
loop operations.  

The proprietary J1939 Command Message (PGN: 65281 through 65407 SA: 34) can be monitored for 
Coil A, Coil B and RPM Setpoints for various operation modes. This address is adjusted based on the 
Module ID. The relationship of the Module ID and the Command Message address is defined in a chart at 
the end of this section.  

The evc/epc can transmit its status over the SAE J1939 Bus. 

The proprietary J1939 Status Message (PGN: 65409 through 65535 SA: 34) is a multiplexed message 
with the first data byte indicating message 1 Status or message 2 Analog Values. This address is 
adjusted based on the Module ID. The relationship of the Module ID and the Status Message address is 
defined in a chart at the end of this section. When the J1939 Command Message is enabled, the Status 
Message will be transmitted.  If Report Analog Values is enabled on the J1939 tab, the Analog Values will 
be transmitted. The content of the Status and Analog Values messages are detailed below. 

 

Command Message Format 

Transmission Repetition 

40mS 

Data Length 

8 

Data Page 

1 

PDU Format 

255 

PDU Specific 

Module ID # 

Priority N/A 
Parameter Group Number 

65281 Through 65407 

(FF01 Through FF7F) 

Start Position 

Length 

Parameter Name 

1 

1 Byte 

Always = 1 

2-3 

2 Bytes 

Coil A Set point 

4-5 

2 Bytes 

Coil B Set point 

6-7 

2 Bytes 

RPM Set point 

 

 

 

 

 

Summary of Contents for epc










































Reviews:

No comments