manualshive.com logo in svg

HCT epc, User Manual, Page: 12 / 41

Share
Download
HCT epc User Manual Download Page 12

 

 

023-00354-Rev1.4      evc/epc 

User 

Manual 

    

 

Copyright © High Country Tek, Inc. – 2013 

 

12

 

evc/epc

 

Controller

  

With

 

SAE

 

J1939

 

Interface

 

Help 

 

Reconnect with controller

:

 T

he GUI will reset communication with the module, and re-read and update 

all variables.  

Print Settings to text

: Will print all settings to your PC default printer, or print to a text file, tab delimited. 

The text file may be viewed with Notepad, Word, or Excel.  

About Controller

: Will display information about the evc/epc, the GUI revision, serial number, contact 

information etc. 

Manual

: Will open the folder in C:\\HCT products/Digital Controllers, or browse to other locations. 

 

Exit 

 

 

Exits the evc/epc GUI and frees up the com port and memory used by the application. 

You can exit the GUI with or without saving the changes. 

 

Dashboard, Status and Graphing Windows 

 

They give real time overview of 
the controller health, operation of 
the system and condition of 
inputs, outputs and any alarms. 

 

 

 

Summary of Contents for epc










































Reviews:

No comments