manualshive.com logo in svg

HCT epc, User Manual, Page: 14 / 41

Share
Download
HCT epc User Manual Download Page 14

 

 

023-00354-Rev1.4      evc/epc 

User 

Manual 

    

 

Copyright © High Country Tek, Inc. – 2013 

 

14

 

evc/epc

 

Controller

  

With

 

SAE

 

J1939

 

Interface

 

Example data files are saved to your PC during the installation. 

When loading factory default data files, select “

Environment

”, then select 

the desired default file.  

 

Default Data files will overwrite any settings in the unit.  

Adjust the Coil Settings first, then other settings as needed. 

 

 

In Agriculture or Automotive you will have 

Four

 files: 

1.  HP Limiting with Variable Command /Anti-stall with Variable Command. 

Monitors RPM, the command in, and adjust the output accordingly. 

 

2.  HP Limiting with fixed command/Anti-stall with fixed command. 

Monitors RPM and adjusts the output accordingly.  

 

3.  Single Coil Pump Control / Valve Control 

Controls the single-coil pump/valve. 

 

4.  Dual Coil Pump Control / Valve Control 

Controls the dual-coil pump(s)/valve(s). 

Summary of Contents for epc










































Reviews:

No comments