manualshive.com logo in svg

HCC Technology POS80B, Technical Manual, Page: 32 / 71

Share
Download
HCC Technology POS80B Technical Manual Download Page 32

Thermal Printer Technical Manual

 

 

 
 

 

                         

                                                         

32

 

 

 

 
 

GS * x y d1...d(x × y × 8)    Define downloaded bit image 

[Name]

            Define downloaded bit image 

[Format]

          ASCII   

 

GS     

*     

x    y    d1...dk 

Hex   

 

1D     

2A     

x    y    d1...dk 

Decimal    

29     

42     

x    y    d1...dk 

[Range]   

      1 ≤ x ≤ 255 

1 ≤ y ≤ 48 
x × y ≤ 800 
0 ≤ d ≤ 255 
k=x× y× 8 

[Description]   

Define a downloaded bit image using the number of dots specified by x and y 
x specifies the number of dots in the horizontal direction. 
y specifies the number of dots in the vertical direction. 
d specifies the data of bit map. 

[Notes] 

 

The number of dots in the horizontal direction is x× 8, in the vertical direction it is y× 8. 
If x× y is out of the specified range, this command is disabled. 
The d indicates bit-image data. Data (d) specifies a bit printed to 1 and not printed to 0. 
The downloaded bit image definition is cleared when: 
ESC @ is executed. 
ESC & is executed. 
FS q is executed. 
2-D bar code is executed. 
Printer is reset or the power is turned off. 
The following figure shows the relationship between the downloaded bit image and the printed 
data. 

Summary of Contents for POS80B








































































Reviews:

No comments