manualshive.com logo in svg

HCC Technology POS80B, Technical Manual, Page: 31 / 71

Share
Download
HCC Technology POS80B Technical Manual Download Page 31

Thermal Printer Technical Manual

 

 

 
 

 

                         

                                                         

31

 

 

 

m 

Mode 

Vertical Direction 

Horizontal Direction 

Number 
of 
Dots 

Dot Density 

Dot 
Density 

Number of Data 
(K) 

0 

8-dot 
single-density 

8 

68 DPI 

101 DPI 

nL + nH × 256 

1 

8-dot 
double-density 

8 

68 DPI 

203 DPI 

nL + nH × 256 

32 

24-dot 
single-density 

24 

203 DPI 

101 DPI 

( nL + nH × 256) × 3 

33 

24-dot 
double-density 

24 

203 DP 

203 DPI 

( nL + nH × 256) × 3 

 
[Notes]

 

 

If  the  values  of  m  is  out  of  the  specified range,  nL  and data  following  are  processed as  normal 
data. 
The  nL  and  nH  indicate  the  number  of  dots  of  the  bit  image  in  the  horizontal  direction.  The 
number of dots is calculated by nL + nH × 256. 
If the bit-image data input exceeds the number of dots to be printed on a line, the excess data is 
ignored. 
d indicates the bit-image data. Set a corresponding bit to 1 to print a dot or to 0 to not print a 
dot. 
After printing a bit image, the printer returns to normal data processing mode. 
This  command  is  not  affected  by  print  modes  (emphasized,  double-strike,  underline,  character 
size or white/black reverse printing), except upside-down printing mode. 
The relationship between the image data and the dots to be printed is as follows: 
When 8-dot bit image is selected: 

 

 
When 24-dot bit image is selected: 

Summary of Contents for POS80B








































































Reviews:

No comments