Hayward Salt & Swim Owner'S Manual Download

Page: 19 / 24

1. Recycle power to the Salt & Swim by unplugging the linecord for two minutes

2. Inspect the Cell. If dirty, follow the Cell cleaning procedure.

3. Check the salt level in the pool and verify the salt level is greater than
2600ppm but also less than 3400ppm.

4. Inspect the Cell Vessel and verify the Cell plates are fully covered by moving

water.

5. Contact Hayward Technical Service.

and then plugging it back in.

1. Recycle power to the Salt & Swim by unplugging the linecord for two minutes

2. Inspect the Cell. If dirty, follow the Cell cleaning procedure.

3. Inspect the

and verify the cell plates are fully covered by moving

water.

5. Contact Hayward Technical Service.

and then plugging it back in.

Cell Vessel

. Inspect the cable that connects the cell to the system. Make sure the cable is

secure and undamaged.

1. Recycle power to the Salt & Swim by unplugging the linecord for two minutes
and then plugging it back in.
2. Contact Hayward Technical Service.

1. Recycle power to the Salt & Swim by unplugging the linecord for two minutes

and then plugging it back in.
2. Contact Hayward Technical Service.

1. Recycle power to the Salt & Swim by unplugging the linecord for two minutes

and then plugging it back in.
2. Contact Hayward Technical Service.

1. Recycle power to the Salt & Swim by unplugging the linecord for two minutes
and then plugging it back in.

2. Perform “Flow Switch Calibration” procedure.
2. Contact Hayward Technical Service.

1. Recycle power to the Salt & Swim by unplugging the linecord for two minutes

and then plugging it back in.
2. Check that the pool temperature does is more than 50ºF and less than 104ºF.
2. Contact Hayward Technical Service.

1. Recycle power to the Salt & Swim by unplugging the linecord for two minutes

and then plugging it back in.
2. Inspect the cable that connects the cell to the system. Make sure the cable is

secure and undamaged.

3. Contact Hayward Technical Service.

1. Recycle power to the Salt & Swim by unplugging the linecord for two minutes
and then plugging it back in.

2. Verify that the Salt & Swim is receiving 120VAC input.
3. Contact Hayward Technical Service.

LED

BLINKING

POSSIBLE ACTIONS

MIN LED

LED 2

LED 5

LED 6

LED 3

LED 4

LED 7

LED 9

MAX LED

Inadequate
Water Flow

Standing By

LED 8

1. Recycle power to the Salt & Swim by unplugging the linecord for two minutes

and then plugging it back in.

3. Inspect the Cell Vessel and verify the cell plates are fully covered by moving
water.

4. Contact Hayward Technical Service.

2. Check that the salt level in the pool is no greater than 3400ppm and/or the
temperature does not exceed 104F.

Summary of Contents for Salt & Swim
























Search results

Summary of Contents for Salt & Swim

Reviews:

Related manuals for Salt & Swim

Brands by name

Popular brands

Hayward Salt & Swim, Owner'S Manual

Search results

Summary of Contents for Salt & Swim

Reviews:

Related manuals for Salt & Swim

Brands by name

Popular brands