background image

When installing and using this electrical equipment, basic safety 

precautions should always be followed, including the following: 

• 

READ AND FOLLOW ALL INSTRUC-

TIONS

• 

TO REDUCE THE RISK OF DROWNING FROM HAIR AND 

BODY ENTRAPMENT, INSTALL A SUITABLY RATED SUCTION 

GUARD TO MATCH THE MAXIMUM FLOW RATE MARKED.  

ATTENTION : LES PRISES DASPIRATION DOIVENT ETRE 

EQUIPEES DE GRILLES CONVENANT AU DEBIT MAXIMAL 

INDIQUE. 

• 

WARNING - To reduce the risk of injury, do not permit children 

to use this product unless they are closely supervised at all 

times.

• 

WARNING – Risk of Electric Shock. Connect only to a grounding 

type receptacle protected by a ground-fault circuit-interrupter 

(GFCI). Contact a qualified electrician if you cannot verify that 

the receptacle is protected by a GFCI.

• 

Do not bury cord. Locate cord to minimize abuse from lawn 

mowers, hedge trimmers, and other equipment. 

• 

WARNING – To reduce the risk of electric shock, replace dam

-

aged cord immediately. 

• 

WARNING – To reduce the risk of electric shock, do not use 

extension cord to connect unit to electric supply; provide a 

properly located outlet. 

• 

“CAUTION: To reduce the risk of electric shock, install at least 

10 feet (3 meters) horizontally from the inside walls of a pool 

or spa/hot tub. Do not use an extension cord.” ATTENTION : 

MAINTENIR UNE DISTANCE MINIMALE D’UN METRE, MESU-

REE DANS UN PLAN HORIZONTAL, ENTRE LE BASSIN ET 

LES APPAREILS ET COMMANDES.

• 

For  Canadian  Units:   At  least  two  lugs  marked  “BONDING 

LUGS” are provided on the external surface or on the inside of 

the supply terminal box or compartment. To reduce the risk of 

electric shock, connect the local common bond

ing grid in the 

area of the hot tub or spa to these terminals with an insulated 

or bare copper conductor not smaller than No. 6 AWG.

• 

SAVE THESE INSTRUCTIONS 

USE ONLY HAYWARD GENUINE REPLACEMENT PARTS

USE ONLY HAYWARD GENUINE REPLACEMENT PARTS

Summary of Contents for Salt & Swim 3C

























Reviews: