Hayward Phantom 6000 Owner'S Manual Download Page 13

Changing Top and Bottom Operation

The Top/Bottom Switch (Part P, p age 4) is set to “AU T O” at the
f a c t o ry. The Phantom Cleaner will vacuum the pool bottom and
sides 2/3 of its cycle and skim the surface 1/3 of its cycle
a u t o m at i c a l ly.

The cleaner can be easily adjusted to concentrate on the areas 
of the pool with the most debris.

• To ONLY clean the bottom and sides of the pool,

m ove the switch to the right “ B OT ” .

• To ONLY skim the pool surfa c e , m ove the switch 

to the left “ T O P ” .

1 3

Use Only Genuine Hayward Replacement Parts.

1 2

Use Only Genuine Hayward Replacement Parts.

Adjusting Sweep Hose Po w e r

• In most pools it will not be necessary to adjust the 

Sweep Hose power.

• O b s e rve the Phantom cleaner operating in the pool.

The Sweep Hose should move in a slow, u n d u l ating 
(snake-like) motion.

Sweep Hose Not Mov i n g :

If the Sweep Hose does not

move side-to-side and just drags behind the cleaner, c h e c k
the Sweep Hose for holes. Check for debris behind the
adjustment knob or in the jet-end of the Sweep Hose.

Sweep Hose Moves Slowly Or Not At All: Turn the
adjustment knob counter- cl o c k w i s e

to increase Sweep

Hose power.

Sweep Hose Frequently Sprays Out Of The Po o l :
Turn the adjustment knob cl o c k w i s e

to reduce Sweep

Hose power.

N o t e :

Do 

N OT

turn the Sweep Hose completely off .

This can cause the hose to tangle or knot.

Phantom Cleaner Adjustments

Warning – Risk of Injury

Turn the Booster Pump and Filtration Pump OFF before
making adjustments to the cl e a n e r. Always make
adjustments outside of the pool. Failure to do so may
cause injury.

Changing Spin-Out Frequency

• In most pools it will not be necessary to change the Spin-Out

f r e q u e n c y.

• The cleaner comes with a 3-prong Spin-Out cam installed,

which makes the Phantom cleaner Spin-Out once every 
5 0 - s e c o n d s . This is ap p r o p r i ate for most pools.

• Pools that are small or have many sharp corners or other

obstacles may benefit from more frequent Spin-Outs. F o r
such pools, open the Cam Cap and replace the 3-prong cam
with the 5-prong 30 second cam.

• Pools that are very large and/or have very few obstacles may

benefit from less frequent Spin-Outs. For such pools, o p e n
the Cam Cap and replace the 3-prong cam with the 2-prong
75-second cam.

• The goal is to maximize cleaning time and minimize the

amount of time spinning out.

• If the cleaner is spending too much time at an obstacle

waiting for a Spin-Out, use a cam with more prongs for more
frequent Spin-Outs.

• If the cleaner rarely needs to Spin-Out near an obstacle then

a cam with fewer prongs and less frequent Spin-Outs will
increase effective cleaning time.

• If the cleaner has a tendency to stay in the deep end (not

cleaning the shallow end suff i c i e n t ly ) , in pools with a
p a r t i c u l a r ly steep or long slopes between the deep and
shallow ends, we recommend using a cam with fewer
p r o n g s , it will promote longer straight runs.

Changing Spin-Out Cam

1 .

Turn the Cam Cap counter clockwise to open.

2 .

Remove the Spin-Out Cam.

3 .

Place the desired Cam in place over the stem.

4 .

Place unused Cams in A c c e s s o ry Bag and store in a safe
place with the Owner’s Guide.

5 .

Close the Cam Cap .

Adjusting Spin-Out Duration

Each Cam has a “ S u m m e r ” side and a “ W i n t e r ” side (see Sun &
S n o w flake logos on each Cam). The Summer side is usually
p r e f e r r e d . If the pool water is cold (below 60 degrees F), t h e
Pressure Hose becomes stiffer and may prevent the Cleaner
from Spinning-Out enough to escape from obstacles. T h e
“ W i n t e r ” Cam side will provide longer Spin-Outs so the Cleaner
o p e r ates better in cold wat e r.

1 .

Turn the Cam Cap to open

2 .

Remove the Cam, turn it over and replace the Cam so the
desired (Sun or Snowflake) side is face-up.

If the cleaner is making more than three attempts to escap e
from an obstacle, use the “ W i n t e r ” s i d e .

If the cleaner regularly spins-out more than three-quarters
of a turn, use the “ S u m m e r ” s i d e .

Cam Cap on Deck

Top/Auto/Bot Switch

Cam Cap Open

Adjusting Sweep Hose Po w e r

Spin-Out Cams

75-Second

50-Second

30-Second

Cam Cap (F)

Cam Cap (F)

Sun Logo

Spin-Out Cam

Summary of Contents for Phantom 6000












































Reviews: