Hayward AquaConnect AQ-CO-HOMENET Troubleshooting Manual Residential Download

Page: 44 / 47

On a router the WAN port should be used for the internet feed, LAN ports are used for

devices like the AquaConnect as well as desktop computers and other similar devices.

PoE ports SHOULD NOT be used as these deliver Power over the Ethernet cable.

Internet

IF connections have been verified and the Tx and Rx

LEDs do not appear, replace the AquaConnect (

AQ-CO-

HOMENET

). IF this does not correct the problem

consult a network professional.

Verify Receptacle Power

Plug the Ethernet into another router port. IF the Tx

and Rx do not appear replace the Ethernet cable and if

LEDs still do not appear go to Step 5D. IF LEDs appear,

teach the AquaConnect (

p. 8

Step 5C

Move/Replace Ethernet Cable

5. NO LEDs Illuminated/Blank

Step 5D

Summary of Contents for AquaConnect AQ-CO-HOMENET















































Search results

Summary of Contents for AquaConnect AQ-CO-HOMENET

Reviews:

Related manuals for AquaConnect AQ-CO-HOMENET

Brands by name

Popular brands

Hayward AquaConnect AQ-CO-HOMENET, Troubleshooting Manual Residential

Search results

Summary of Contents for AquaConnect AQ-CO-HOMENET

Reviews:

Related manuals for AquaConnect AQ-CO-HOMENET

Brands by name

Popular brands