Hayward Aqua Trol AQ-TROL-RJ-CUL, Operation And Installation Manual

Page: 3 / 8

Table of Contents
OPERATION OPERATION
OPERATION OPERATION OPERATION
The Aqua Trol The Aqua Trol
The Aqua Trol The Aqua Trol The Aqua Trol
® ® ® ® ®
............................................................................1
Water Chemistry Water Chemistry Water Chemistry Water Chemistry Water Chemistry.......................................................................2
Controls Controls
Controls Controls Controls.......................................................................................5
Maintenance Maintenance Maintenance Maintenance Maintenance...............................................................................6
.
INSTALLATION INSTALLATION INSTALLATION INSTALLATION INSTALLATION
Mounting Mounting Mounting Mounting Mounting......................................................................................8
Plumbing Plumbing Plumbing Plumbing Plumbing......................................................................................9
Wiring Wiring Wiring Wiring Wiring..........................................................................................9
TROUBLESHOOTING TROUBLESHOOTING
TROUBLESHOOTING TROUBLESHOOTING TROUBLESHOOTING
Troubleshooting Troubleshooting
Troubleshooting Troubleshooting Troubleshooting.......................................................................10
WARRANTY WARRANTY
WARRANTY WARRANTY WARRANTY
Warranty Warranty Warranty Warranty Warranty....................................................................................12
11
2. "Generating" LED not on
The Aqua Trol only generates chlorine when the filter pump is running, the main
switch is in the "AUTO" or "SUPER CHLORINATE" position, and none of the red
fault LEDs are illuminated.
3. "Generating" LED flashing
The temperature of the pool water is too high or low to operate. You can override this
by switching the main switch to SUPER CHLORINATE. The Aqua Trol will run at
maximum output for the remainder of the current pump cycle or 24 hours, whichever
comes first.
4. "Check Salt" LED illuminated or flashing
Take a sample of your pool water to your local Authorized Aqua Rite Dealer Hayward
and have the salt level tested. No salt test is completely accurate and the test results
may vary from the salt level on the Aqua Trol display. If salt level is low, add salt
according to chart on page 4.
5. "High Salt" LED illuminated
Check salt level in pool/spa. If salt level is too high, lower salt level by draining some
of the pool water out of the pool and replace with fresh water. Continue until the salt
concentration is at recommended levels.
6. "Inspect Cell" LED flashing
Inspect and clean cell according to directions on page 8. When done, press the
"diagnostic" button for 3 seconds to stop the "Inspect Cell" LED flashing.
7. "Inspect Cell" LED illuminated
Remove and inspect the cell for scale. If the cell is scaled, follow the directions on
page 8 for cell cleaning. If the pool has the proper amount of salt and the "Inspect
Cell" LED is still illuminated, the cell may be worn and need replacement.
8. Possible causes of little or no free chlorine residual
- Aqua Trol switch in OFF position.
- Desired Output % adjustment setting is too low.
- Low stabilizer (Cyanuric Acid).
- Filter pump switched off or filter pump time too short (8 hours for average size
pools, more for large pools)
- Salt level too low (below 2500 ppm, Low Salt LED on).
- Salt level too high (High Salt LED on).
- Very warm pools increase chlorine demand--increase Desired Output % or filter
run time.
- Cold water (below 50ºF) causes Aqua Trol to stop generating (Generating LED
flashing).
- Excessive scaling on cell.
- High level of Nitrogen in pool water.
- "Yellow Out" or similar treatment recently used. Some yellow algae treatments will
use chlorine at a very high rate and deplete the residual free chlorine. Manually
shock the pool if indicated in the directions on the algae treatment. It still may be
a matter of days before the pool returns to "normal" and chlorine tests will show
the desired 1-3ppm free chlorine reading.
9. "-Pcb-" displayed and all 4 red/yellow LEDs are illuminated.
A possible Printed Circuit Board fault has been detected.