Hawk Intelligent 2000 Series Instruction Manual Download Page 9

9

Overview

Series  2000  HART                                                             

Transmitter type and options

Equipment category

Ambient temperature range

Pressure / Level Transmitter
Series 2000, Series 2000-SAN, Series 2000-Cable,
Series 2000-SAN-Cable, Series CER-2000,
Series 2000-Hydrobar-Cable and
Series 2000-Hydrobar-EXTD

II 1 G

-20ºC………70ºC

With transparent indicator cover (Option I)

II 1 G

-20ºC………70ºC

Pressure / Level Transmitter
Series 2000, Series 2000-SAN, Series 2000-Cable
And Series 2000-SAN-Cable. 
With closed covers, Option G180

II 3 G

-20ºC………70ºC

Process temperature range: 
-20 °C to +100 °C

Pressure / Level Transmitter
Series 2000, Series 2000-SAN, Series 2000-Cable,
Series 2000-SAN-Cable, Series CER-2000,
Series 2000-Hydrobar-Cable, Series 2000-Hydrobar-
EXTD and Temperature Transmitter Type TT-2000
With closed covers, Option G100

II 1G

and

II 1D

-20 °C to +70 °C

The maximum surface temperature of the enclosure T 100ºC is based on a maximum ambient temperature of 70ºC, and maximum 
process temperature of 100°C. This temperature is determined with a dust layer of maximum 5 mm.

Electrical data for Ex transmitters 

Pressure / Level Transmitter Series 2000, Series 2000-SAN, Series 2000-Cable, Series 2000-SAN-Cable, Series CER-2000, Series 
2000-Hydrobar-Cable, Series 2000-Hydrobar-EXTD and Temperature Transmitter Type TT-2000: 
Supply/output circuit (terminals 3 ‘-’ and 4 ‘+’): in type of protection intrinsic safety Ex ia IIC, or
Ex ia lllC only for connection to a certified intrinsically safe circuit, with the following maximum values: Ui = 26,5 Vdc; Ii = 110 mA; Pi = 
0,9 W (linear source); Li = 1,4 mH; Ci = 63 nF (without cable between terminals 3 ‘-’ and 4 ‘+’).

Cable length

The maximum length of the cable for the Series 2000-Cable, 2000-SAN-Cable and 2000- Hydrobar-Cable is 100 m. Electrostatic 
charging of the cable and the protection cap by the flow of non-conductive media (e.g. in stirring vessels or pipes) shall be avoided.

Special conditions for Safe use in Zone 0

As category 1G equipment may be applied directly in the process, electrostatic discharge from the cable and the protection cap 
of Pressure / Level Transmitter Series 2000-Hydrobar-Cable by the flow of non-conductive media (e.g. in stirring vessels or pipes) 
should be avoided.

Special Instructions for Safe use in Zone 2

For use in non-sparking areas (Zone 2), the following should be taken into consideration:
• As standard the transmitter is supplied without a certified cable gland. The cable entry is fitted with a PE blanking plug for protection  
  during transport. Remove the blanking plug after installing the transmitter. When using a gland make sure it is certified and   
  complying with applicable protection level of the transmitter.
• Always use the covers supplied by Klay Instruments B.V.
• All transmitters from Klay Instrument are designed to last for at least 10 years under normal process and environmental conditions.  
  The gaskets and seals for the series 2000 are successfully tested according to IEC 60079-0 for temperature endurance (heat and  
  cold), resistance to impact and ingress protection by DEKRA Certification. In harsh process and environmental conditions the  
  lifetime of gaskets and seals may be reduced.
Hawk Measurement strongly advises to inspect these yearly and replace them when necessary. 

Summary of Contents for Intelligent 2000 Series

























Reviews: