PSC1502 AUDIO SYSTEMS
INSTALLATION GUIDE
HAWG WIRED
PAGE 7
NEWARK, CA
I
I
N
N
S
S
T
T
A
A
L
L
L
L
A
A
T
T
I
I
O
O
N
N
I
I
N
N
S
S
T
T
R
R
U
U
C
C
T
T
I
I
O
O
N
N
S
S
[
[
C
C
O
O
N
N
T
T
I
I
N
N
U
U
E
E
D
D
]
]
WIRING THE MAIN AMPLIFIER
(CONTINUED)
9.
DETERMINE AND CONNECT YOUR SOURCE UNIT OUTPUT TO THE AMPLIFIER INPUT CABLE(S)
USING ONE OF THE FOLLOWING HIGH OR LOW LEVEL INPUT METHODS:
9.1.
FACTORY SOURCE UNITS - HIGH LEVEL INPUT (NO RCA CONNECTORS AVAILABLE)
CONNECT THE FRONT SPEAKER OUTPUT WIRES FROM THE SOURCE UNIT TO THE HIGH
LEVEL INPUT CABLE (USE ATTACHED TERMINALS TO CONNECT INPUT WIRES TO THE
SPEAKER WIRE TERMINALS IF POSSIBLE).
NOTE: FOR CUSTOM WIRING CONNECTIONS, WE RECOMMEND CRIMP, SOLDER, AND HEAT SHRINK.
HIGH LEVEL INPUT CABLE(S)
CONNECT
TOGETHER
H-D® SOURCE UNIT MODELS
2 CHANNEL – USE FRONT ONLY
4 CHANNEL – USE BOTH
1998-2005
8 OHM
1998-20XX
CVO
1
2006-20XX
2 OHM
FRONT LEFT +
WHT
f
f
e
e
WHT/ORG
(PIN 16)
WHT/ORG
(PIN 16)
WHT/ORG
(PIN 16)
FRONT LEFT –
BLK (WHT TWIST)
f
f
e
e
L.GRN/WHT
(PIN 17)
L.GRN/WHT
(PIN 17)
L.GRN/WHT
(PIN 17)
FRONT RIGHT +
RED
f
f
e
e
GRY/RED
(PIN 18)
GRY/RED
(PIN 18)
GRY/RED
(PIN 18)
FRONT RIGHT –
BLK (RED TWIST)
f
f
e
e
L.GRN/BLK
(PIN 1)
L.GRN/BLK
(PIN 1)
L.GRN/BLK
(PIN 1)
PIN NUMBERS APPLY TO H-D MAIN HARNESS CONNECTOR
NOTE
1
: CVO BIKES MAY BE EQUIPPED WITH A HIGH-OUTPUT SOURCE UNIT; DO NOT USE THE FOLLOWING WIRE
COLORS: WHT/PNK, PNK, WHT/GRY, GRY. THESE OUTPUTS CAN DAMAGE THE AMPLIFIER INPUTS.
9.2.
AFTERMARKET SOURCE UNITS - LOW LEVEL INPUT (RCA CONNECTORS AVAILABLE)
CONNECT THE FRONT RCA OUTPUT CONNECTORS FROM THE SOURCE UNIT TO THE LOW
LEVEL INPUT CABLE AND INPUT JACK ON THE FRONT OF THE AMPLIFIER.
NOTE: VERY LITTLE DIELECTRIC GREASE IS NEEDED TO KEEP YOUR CONNECTIONS CORROSION FREE. VERY LITTLE
MOISTURE IS NEEDED TO CORRODE CONTACTS NOT COVERED WITH DIELECTRIC GREASE.
10.
PLUG THE CHOSEN INPUT CABLE INTO THE CORRESPONDING CONNECTOR OF THE MAIN
AMPLIFIER LABELED HIGH OR LOW ACCORDINGLY.
WIRING THE SPEAKERS
11.
REMOVE STOCK SPEAKERS FROM THE BIKE AND INSTALL 4 OHM SPEAKERS OF YOUR CHOICE.
NOTE: IF YOU ARE INSTALLING HAWG WIRED SPEAKERS, REFER TO THE INSTALLATION INSTRUCTIONS THAT
CAME WITH THEM. IF INSTALLING ANOTHER BRAND OF SPEAKERS, REFER TO THOSE SPECIFIC MANUFACTURER
INSTRUCTIONS IF NECESSARY.
12.
ROUTE AND CONNECT THE SPEAKER WIRES FROM EACH SPEAKER OF YOUR SYSTEM TO THE
CORRESPONDING SPEAKER OUTPUT TERMINAL BLOCK ON THE AMPLIFIER (RIGHT/LEFT).
NOTE: KEEP THE POLARITIES (+/–) OF EACH WIRE PAIR CORRECT BETWEEN THE AMPLIFIER(S) AND SPEAKERS.
IF YOU ARE INSTALLING HAWG WIRED SPEAKERS, REFER TO THE INSTALLATION INSTRUCTIONS THAT CAME
WITH THEM. IF INSTALLING ANOTHER BRAND OF SPEAKERS, REFER TO THOSE SPECIFIC MANUFACTURER
INSTRUCTIONS IF NECESSARY.
