Haussmann 8400048, Operator'S Manual

Page: 8 / 15

E
N
G
L
IS
H
HEADING
14
E
N
G
L
IS
H
HEADING DESCRIPTION, SPECIFICATIONS AND INSTRUCTIONS TABLE OF CONTENTS
1. Laser light assembly
2. Laser light on/off button
3. Laser light aperture
4. Trigger switch
5. Lock-off button
6. Motor housing
7. Main handle
8. Front handle
9. Bevel adjustment knob
10. Bevel scale
11. Parallel fence locking knob
12. Parallel fence
13. Blade guard lever
14. Lower blade guard
15. Base plate
16. Upper blade guard
17. Dust extraction port
18. Depth locking lever
19. Depth of cut indicator
20. Spindle lock button
21. Blade
22. Blade wrench storage
area (back of saw)
23. Blade wrench
24. Blade guide notch
DESCRIPTION OF SYMBOLS
The rating plate on your tool may show symbols. These represent important
information about the product or instructions on its use.
Wear hearing protection.
Wear eye protection.
Wear breathing protection.
Double insulated for additional protection.
Conformance to use the ETL mark
and compliance with Standards
ENVIRONMENTAL PROTECTION
Please discard or recycle your product and its packaging according to
your municipal bylaws.
WARNINGS
1. Do not attempt to change the position of the laser under any
circumstances, it has been set at the factory and is accurately focused
on the center of the saw blade.
2. It may be more difficult to see the laser line in conditions of bright
sunshine and on certain surfaces.
SPECIFICATIONS
•
Voltage : 120V ~ 60Hz
•
Power rating : 15 Amp
•
No-load speed : 4,700 RPM
•
Blade diameter : 7 1/4" (184 mm)
•
Blade teeth : 40
•
Blade arbour : 5/8" (16 mm)
•
Blade kerf : 3/32" (2.4 mm)
•
Bevel capacity : 0° to 55°
•
Depth of cut at 90° : 2 1/4" (58 mm)
•
Depth of cut at 45° : 1 1/2" (40 mm)
•
Weight : 10.56 lbs (4.8 kg)
SAFETY RULES FOR LASER LIGHTS
The laser guide used in the tool is Class II with a maximum output of 1mW and
a wavelength of 650nm. The laser guide does not normally present an optical
hazard, although staring at the beam may cause flash blindness.
USER INFORMATION
CAUTION. The use of optical instruments with this laser product will
increase the chance of eye damage.
•
Do not stare into the laser beam.
•
The laser shall be used and maintained in accordance with the
manufacturer’s instructions.
•
Never aim the beam at any person or an object other than the work piece.
•
Always ensure the laser beam is aimed at a sturdy work piece without a
reflective surface (i.e. wood or rough coated surfaces are acceptable).
Bright shiny reflective sheet or the like is not suitable for laser use as
the reflective surface could direct the beam back at the operator.
AVERTISSEMENT CAUTION
RAYONNEMENT LASER - NE PAS REGARDER LE RAYON NI
VISUALISER DIRECTEMENT À L'AIDE D'INSTRUMENTS D'OPTIQUE
LASER RADIATION – DO NOT STARE INTO BEAM
OR VIEW DIRECTLY WITH OPTICAL INSTRUMENTS
Longueur d’onde / Wavelength: 650 nm
Puissance max. / Max Output: 1 mW
Produit laser de classe II / Class II Laser Product
Conforme aux parties 1040.10 et 1040.11
de la norme FDA21 CFR
Complies with FDA21 CFR Parts 1040.10 and 1040.11
ÉVITER L’EXPOSITION – Un rayonnement laser passe par cette ouverture
AVOID EXPOSURE – Laser radiation is emitted through this aperture
KNOW YOUR PRODUCT
•
Know your product 14
•
Description, specifications and instructions 15
•
General safety instructions 16
•
Additional safety rules for circular saws 18
•
Operating instructions 20
•
Maintenance 24
•
Warranty 24
15
1
2
3
5
6
8
10
11
13
15
16
17
24
14
21
7
4
19
18
23
12
20
9