Haulotte H12SX Maintenance Book Download Page 69

Page: 69 / 128

4001015340

E 12.18

USA / GB

Replacement-Tightening

Wheel

M006

Replacement-Tightening

Wheel

1 - You will need

2 - Preliminary procedure

Place the machine in maintenance configuration.

3.3.1 -Placing the machine in maintenance

configuration

3 - Criteria of replacement

Replace the wheels and the tires if any of the following conditions exist :

• Presence of cracks, damage, deformation or other faults on the hub

• Damage to the tire :

• Cut or hole > 3 cm (2 in) in the rubber side wall.

• Blister or pronounced lump on the external and lateral wall.

• Damaged wheel stud.

• Damage or wear on the side wall to the extent that the reinforcing wire is visible.

• Nonlinear wear of the ground contact surface greater than 10 %.

• Standard tool kit
• Protective goggles
• Gloves
• Jack
• Hoist
• Torque spanner

• Place barriers around the perimeter of the work area

Summary of Contents for H12SX

































































































































Search results

Summary of Contents for H12SX

Reviews:

Related manuals for H12SX

Brands by name

Popular brands

Haulotte H12SX, Maintenance Book

Search results

Summary of Contents for H12SX

Reviews:

Related manuals for H12SX

Brands by name

Popular brands