MAINTENANCE
Form No. ITQm-0313
9
English
General
Hatco Intelligent Toast-Qwik
®
Conveyor Toasters are designed
for maximum durability and performance with minimum
maintenance.
ELECTRIC SHOCK HAzARD:
• Put unit in standby, allow to cool, turn OFF power
switch, and unplug power cord before performing
cleaning, adjustments, maintenance, or attempting to
clear a jam.
• DO NOT submerge or saturate with water. Unit is not
waterproof. Do not operate if unit has been submerged
or saturated with water.
• Do not steam clean or use excessive water on unit.
• This unit is not “jet-proof” construction. Do not use jet-
clean spray to clean this unit.
• Do not clean unit when it is energized or hot.
• Do not allow liquids to spill into unit.
• This unit must be serviced by qualified personnel only.
Service by unqualified personnel may lead to electric
shock or burn.
• Use only Genuine Hatco Replacement Parts when
service is required. Failure to use Genuine Hatco
Replacement Parts will void all warranties and may
subject operators of the equipment to hazardous
electrical voltage, resulting in electrical shock or burn.
Genuine Hatco Replacement Parts are specified to
operate safely in the environments in which they are
used. Some aftermarket or generic replacement parts
do not have the characteristics that will allow them to
operate safely in Hatco equipment.
This unit has no “user-serviceable” parts. If service is
required on this unit, contact an Authorized Hatco Service
Agent or contact the Hatco Service Department at
800-558-0607 or 414-671-6350; fax 800-690-2966; or
International fax 414-671-3976.
Daily Cleaning
To preserve the finish of the toaster, it is recommended that the
metal surfaces be cleaned daily.
Submerging or saturating unit with water will damage the
unit and void unit warranty.
Use non-abrasive cleaners and cloths only. Abrasive
cleaners and cloths could scratch finish of unit, marring its
appearance and making it susceptible to soil accumulation.
Clean unit daily to avoid malfunctions and maintain
sanitary operation.
1. Perform the “Daily Shutdown” procedure in the
OPERaTION section, and unplug the power cord.
2. Remove and empty the crumb tray and the toast chute.
a. Wash the crumb tray and the toast chute with warm
water and a mild detergent. Rinse with water.
b. allow the crumb tray and toast chute to air dry, or dry
with a soft cloth.
WARNING
WARNING
NOTICE
BURN HAzARD: Do not remove crumb tray for cleaning
until toaster is cool.
3. Wipe the exterior surfaces of the toaster with a non-
abrasive, damp cloth.
4. Stubborn stains may be removed with a good stainless
steel cleaner or a non-abrasive cleaner. Hard to reach
areas should be cleaned with a small brush and mild soap.
5. Reinstall the crumb tray and toast chute. Refer to the
INSTaLLaTION section for instructions.
Cleaning the Bottom Element Reflector
The bottom element reflector inside the toasting chamber has
slots that allow bread crumbs to drop through to the crumb tray.
Over an extended period of use, bread crumbs may build up on
the reflector and not drop through onto the tray.
1. Perform the “Daily Shutdown” procedure in the
OPERaTION section, and unplug the power cord.
2. Wipe the crumbs onto the crumb tray using a bristle brush.
• To wipe the reflector, place the bristle brush through the
conveyor belt and wipe to each side.
3. Perform the “Daily Cleaning” procedure in this section.
Cleaning the Fan Filters
Two cooling fan filters are located on
the bottom of the unit. These filters
should be checked/cleaned monthly
or anytime the Warning light comes
on. Use the following procedure to
clean the filters.
1. Perform the “Daily Shutdown”
procedure in the OPERaTION section, and unplug the
power cord.
2. Carefully lay the unit on its side to access the fan filters on
the bottom of the unit.
3. Pull the filter assembly off of each fan housing.
4. Remove the filter from each of the filter assemblies.
5. Rinse the filters using hot water. allow the filters to dry
completely.
6. Place the filters back inside the filter assemblies.
7. Snap a filter assembly onto each filter housing.
8. Return the unit to its upright position.
CAUTION
Warning
Light
Warning
Light
