Merchandising Decal
Self-adhesive merchandising decals are available to promote
food products. The decals are designed to be installed on three
(3) sides of the cabinet above the glass panels. Merchandising
decals are red with yellow letters reading HOT PIZZA or HOT
PRETZELS. A graphic decal featuring pizza illustrations is also
available.
Decal Installation
1. Before installing decals, clean the side panels with a non-
oily cleaner, such as isopropyl alcohol (rubbing alcohol).
2. After the cleaned surfaces have dried, remove the
protective backing from the decal and apply to the panel.
3. Any air pockets or bubbles behind the sticker can be
removed by rubbing gently with a soft cloth from the center
towards the outer edges.
Figure 16. Decal Installation
sign holders
(FDWD-1, FDWD-1x, FDWD-2, and FDWD-2x)
Use the following procedures to install either a Display Sign
Holder(s) or the Three-Sided Sign Holder.
eLeCTRIC shOCK hAzARD: Turn the power switch OFF,
unplug the power cord, and allow the unit to cool before
performing any maintenance or cleaning.
Display sign holder Installation
Display Sign Holders can be installed on any side of the unit
except the control side. Up to three Display Sign Holders can
be installed on a unit. There are two height sizes available for
display sign holders, 3″ and 6-3/8″.
NOTE: Signage not supplied by Hatco. Sign dimensions are:
3″ Holder = 19-1/16″ W (484 mm) x 3-1/4″ H (83 mm)
6-3/8″ Holder = 19-1/16″ W (484 mm) x 6-3/8″ H (162 mm)
Order custom signs for Hatco equipment at
www.hatcographics.com
.
1. Remove the appropriate hood mounting screws from the
cabinet hood. The screws that need to be removed are
determined by the location and number of sign holders
being installed.
2. Align the mounting holes on the sign holder(s) with the
mounting holes in the cabinet hood.
3. Insert the hood mounting screws through the holes in the
sign holder(s) and into the cabinet hood. Tighten securely.
Decal
WARNING
NOTE: if more than one display sign holder is being installed,
some of the hood mounting screws may need to thread
through and secure two display sign holders.
4. Place the polycarbonate window(s) into sign holder.
Figure 17. Display Sign Holder Installation
Three-sided sign holder Installation
The Three-Sided Sign Holder can be installed on the cabinet in
place of the cabinet hood. The Three-Sided Sign Holder will be
installed at the factory if ordered at the time of sale, but can be
retro-fitted using the following procedure.
NOTE: The Three-Sided Sign Holder is available on FDWD-1
and FDWD-1X models only and comes installed when
ordered with the unit.
NOTE: Signage not supplied by Hatco. Sign dimensions are
19-5/16″ W (491 mm) x 6-5/8″ H ( 168 mm). Order custom
signs for Hatco equipment at
www.hatcographics.com
.
1. Remove the four hood mounting screws from the cabinet
hood.
2. Remove the cabinet hood.
3. Place the sign holder assembly on the cabinet and align it
with the cabinet hood mounting holes.
4. Insert the four hood mounting screws through the holes in
the sign holder assembly and into the cabinet.
5. Tighten all screws.
6. Place the polycarbonate window(s) into sign holder.
Figure 18. Three-Sided Sign Holder Installation
Hood Mounting
Screw
Three-Sided
Sign Holder
Cabinet
Hood
(remove)
Hood Mounting
Screw
Display
Sign Holder
Cabinet
Hood
17
Form No. FDWDM-1010
OPTIONs AND ACCessORIes
Summary of Contents for FLAV-R-FRESH FDWD-1
Page 19: ...19 Form No FDWDM 1010 NOTes...